816368
18
Zoom out
Zoom in
Previous page
1/300
Next page
18
English
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your
dealer or the HiKOKI Authorized Service Center.
1. Power tool
Symptom Possible cause Remedy
Tool doesn’t run No remaining battery power Charge the battery.
Battery isn’t fully installed. Push the battery in until you hear a click.
Tool suddenly stopped Motor is overloaded Get rid of the problem causing the
overloaded.
Overload protection is in operation.
The battery is overheated. Let the battery cool down.
Suddenly stopped Motor was continuously overloaded. Refer to “LED LIGHT WARNING SIGNALS”.
Motor speed declined
during operation Motor was continuously overloaded. Refer to “LED LIGHT WARNING SIGNALS”.
Doesn’t cut well The saw blade is worn or missing teeth. Replace with a new saw blade.
The bolt is loose. Firmly tighten the bolt.
The saw blade is installed backwards. Install the saw blade in the proper direction.
Switch can’t be pulled The switch lock is not pushed in enough. Push the switch lock in all the way.
Sawdust discharge is poor Sawdust has accumulated in the saw cover. Remove the sawdust inside the saw cover.
Battery cannot be installed Attempting to install a battery other than that
speci ed for the tool. Please install a multi volt type battery.
Information concerning airborne noise and vibration
The measured values were determined according to
EN62841 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 112 dB (A)
Measured A-weighted sound pressure level: 101 dB (A)
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN62841.
Cutting metal:
Vibration emission value ah = 1.9 m/s2
Uncertainty K = 1.5 m/s2
The declared vibration total value and the declared noise
emission value have been measured in accordance with a
standard test method and may be used for comparing one
tool with another.
They may also be used in a preliminary assessment of
exposure.
WARNING
The vibration and noise emission during actual use
of the power tool can di er from the declared total
value depending on the ways in which the tool is used
especially what kind of workpiece is processed; and
Identify safety measures to protect the operator that
are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched o and when it is running idle in addition to the
trigger time).
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
00BookCD3605DBEU.indb1800BookCD3605DBEU.indb18 2022/06/2215:19:392022/06/2215:19:39
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CD3605DB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CD3605DB in the language / languages: All languages as an attachment in your email.

The manual is 13.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info