816368

Hikoki CD3605DB Manual

17
Zoom out
Zoom in
Previous page
1/300
Next page
17
English
Table 3
Protective Function Overheat Protection Overload Protection
Tool Status Motor stopped during operation Motor stopped during operation
LED Lighting Status 0.5 second 0.1 second
Lighting Condition of
the Display Lamp Power mode: Light OFF
Silent mode: Light ON Power mode: Light OFF
Silent mode: Light ON
Cause Motor at high temperature Motor is overloaded
Countermeasure Allow the unit to fully cool down.
LED blinking should stop approximately
10 seconds after releasing the switch.
Remove the cause of the overload.
LED blinking should stop approximately
10 seconds after releasing the switch.
6. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
7. Storage
Store the power tool and battery in a place in which
the temperature is less than 40°C and out of reach of
children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signifi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modifi ed (such as
disassembly and replacement of cells or other internal
parts).
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country specifi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
DISPOSING OF CHIPS (Fig. 25)
WARNING
When disposing chips, make sure that the tool is
switched off and that the battery is removed.
NOTE
○ Immediately after cutting steel materials, the chips and
the dust box may be hot. Do not touch them directly.
○ When disposing of the chips, do not allow the chips to
enter the motor portion of the tool body or the battery
mount.
○ Before changing the material to cut, dispose of the chips
that are in the dust box.
CAUTION
○ Dispose of the chips that are in the dust box before they
accumulate above the marks.
○ Failure to do so will reduce the effi ciency of the dust
collecting. Additionally, the heat of the chips may deform
the dust box.
(1) Press the hook on the bottom of the dust cover, open the
dust cover, and dispose of the chips that are in the dust
box.
(2) Close the dust cover, and fasten the hook.
MAINTENANCE AND INSPECTION
1. Inspecting the saw blade
Since use of as dull saw blade will degrade effi ciency
and cause possible motor malfunction, sharpen or
replace the saw blade as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Motor unit maintenance
The motor winding is an important part of this tool. Avoid
damaging and be careful to avoid contact with cleaning
oil or water.
Dust or particle accumulation in the motor can result in
damage.
4. Inspecting and maintaining the lower guard
Always make sure that the lower guard moves smoothly.
In the event of any malfunction, immediately repair the
lower guard.
5. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
00BookCD3605DBEU.indb1700BookCD3605DBEU.indb17 2022/06/2215:19:392022/06/2215:19:39
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CD3605DB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CD3605DB in the language / languages: All languages as an attachment in your email.

The manual is 13.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info