Manual Hikoki C12RSH2 (page 37 of 284) (All languages)

816406

Zoom out

Zoom in

1/284

English

3. Positioning the table insert (Fig. 13)

Table inserts are installed on the turntable. When

shipping the tool from the factory, the table inserts are

so ﬁ xed that the saw blade does not contact them. The

burr of the bottom surface of the workpiece is remarkably

reduced, if the table insert is ﬁ xed so that the gap

between the side surface of the table insert and the saw

blade will be minimum. Before using the tool, eliminate

this gap in accordance with the following procedure.

(1) Right angle cutting

Loosen the three 5 mm machine screws, then secure

the left side table insert and temporarily tighten the 5 mm

machine screws of both ends. Then ﬁ x a workpiece

(about 200 mm wide) with the vise assembly and cut it

oﬀ . After aligning the cutting surface with the edge of the

table insert, securely tighten the 5 mm machine screws

of both ends. Remove the workpiece and securely

tighten the 5 mm center machine screw. Adjust the right

hand table insert in the same way.

(2) Left and right bevel angle cutting

Adjust the table insert in the manner same procedure for

right angle cutting.

CAUTION

After adjusting the table insert for right angle cutting, the

table insert will be cut to some extent if it is used for bevel

angle cutting.

When bevel cutting operation is required, adjust the

table insert for bevel angle cutting.

4. Conﬁ rmation for use of sub fence (A) (Fig. 14)

WARNING

When right angle cutting, loosen the 6 mm wing bolt, then

slide the sub fence (A) outward and remove it. Failure to

do so may result in the main body or saw blade coming

into contact with the sub fence (A) and causing injury.

This power tool is equipped with a sub fence (A).

In the case of direct angle cutting and left bevel angle

cutting, use the sub fence (A). Then, you can realize

stable cutting of the material with a wide back face.

When right angle cutting, loosen the 6 mm wing bolt,

then slide the sub fence (A) outward and remove it, as

shown in Fig. 14.

5. Conﬁ rmation for use of sub fence (B) (Fig. 14)

WARNING

When left angle cutting, loosen the 6 mm wing bolt, then

slide the sub fence (B) outward. Failure to do so may

result in the main body or saw blade coming into contact

with the sub fence (B) and causing injury.

This power tool is equipped with a sub fence (B). In the

case of direct angle cutting and right bevel angle cutting,

use the sub fence (B). Then, you can realize stable

cutting of the material with a wide back face. When left

angle cutting, loosen the 6 mm wing bolt, then slide the

sub fence (B) outward, as shown in Fig. 14.

6. Installing the sub table (Fig. 15)

Using an item such as a steel square, match the upper

surfaces of the base surface and sub table. Adjust the

vertical level of the sub table by turning the 8 mm height

adjustment bolt. After the adjustment, secure the holder

with the 8 mm bolt on the rear of the base, and secure the

6 mm knob bolt of the sub table.

7. Using an ink line (Adjusting the guard)

(1) Right angle cutting

Loosen the 6 mm knob bolt and contact the tip of the

guard with the workpiece.

Aligning the ink line on the workpiece with the groove of

the guard, the workpiece is cut on the ink line.

(2) Miter cutting and compound cutting (Miter cutting +

bevel cutting)

Upon lowering the motor section, the lower guard is

raised and the saw blade appears.

Align the ink line with the saw blade.

CAUTION

In some arrangements when the turntable is rotated, the

guard projects from the fence surface. Loosen the 6 mm

knob bolt and push the guard to the retracted position.

Never lift the lower guard while the saw blade is rotating.

When cutting at an angle of 45° to the right or more,

please slide the guard to the rear.

The guard and sub-fence (A) and sub-fence (B) will not

only make contact and adversely aﬀ ect cutting accuracy,

this could also result in damage to the guard.

8. Position adjustment of laser line

Ink lining can be easily made on this tool to the laser

marker. A switch lights up the laser marker (Fig. 16).

Depending upon your cutting choice, the laser line can

be aligned with the left side of the cutting width (saw

blade) or the ink line on the right side.

The laser line is adjusted to the width of the saw blade at

the time of factory shipment. Adjust the positions of the

saw blade and the laser line taking the following steps to

suit the use of your choice.

(1) Light up the laser marker and make a groove of about 5

mm deep on the workpiece that is about 20 mm in height

and 150 mm in width. Hold the grooved workpiece by

vise as it is and do not move it. For grooving work, refer

to “18. Groove cutting procedures”.

(2) Then, turn the adjuster and shift the laser line. (If you turn

the adjuster clockwise, the laser line will shift to the right

and if you turn it counterclockwise, the laser line will shift

to the left.) When you work with the ink line aligned with

the left side of the saw blade, align the laser line with the

left end of the groove (Fig. 17). When you align it with

the right side of the saw blade, align the laser line with

the right side of the groove.

(3) After adjusting the position of the laser line, draw a right-

angle ink line on the workpiece and align the ink line

with the laser line. When aligning the ink line, slide the

workpiece little by little and secure it by vise at a position

where the laser line overlaps with the ink line. Work on

the grooving again and check the position of the laser

line. If you wish to change the laser line’s position, make

adjustments again following the steps from (1) to (3).

WARNING

○ Make sure before plugging the power plug into the

receptacle that the main body and the laser marker are

turned oﬀ .

○ Exercise utmost caution in handling a switch trigger for

the position adjustment of the laser line, as the power

plug is plugged into the receptacle during operation.

If the switch trigger is pulled inadvertently, the saw blade

can rotate and result in unexpected accidents.

○ Do not remove the laser marker to be used for other

purposes.

CAUTION (Fig. 18)

○ Laser radiation - Do not stare into beam.

○ Laser radiation on work table. Do not stare into beam. If

your eye is exposed directly to the laser beam, it can be

hurt.

○ Do not dismantle it.

○ Do not give strong impact to the laser marker (main body

of tool); otherwise, the position of a laser line can go out

of order, resulting in the damage of the laser marker as

well as a shortened service life.

○ Keep the laser marker lit only during a cutting operation.

Prolonged lighting of the laser marker can result in a

shortened service life.

○ Use of controls or adjustments or performance of

procedures other than those speciﬁ ed herein may result

in hazardous radiation exposure.

NOTE

○ Perform cutting by overlapping the ink line with the laser

line.

00BookC12RSH2.indb3700BookC12RSH2.indb37 2021/11/0912:16:172021/11/0912:16:17

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki C12RSH2 in the language / languages: All languages as an attachment in your email.

The manual is 9.45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hikoki C12RSH2 Manual

Product: