Manual Hikoki C12RSH2 (page 33 of 284) (All languages)

816406

Zoom out

Zoom in

1/284

English

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

SAFETY INSTRUCTIONS FOR MITER

SAW

a) Miter saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-

oﬀ wheels for cutting ferrous material such as bars,

rods, studs, etc.

Abrasive dust causes moving parts such as the lower

guard to jam. Sparks from abrasive cutting will burn the

lower guard, the kerf insert and other plastic parts.

b) Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand.

If your hand is placed too close to the saw blade, there is

an increased risk of injury from blade contact.

c) The workpiece must be stationary and clamped or

held against both the fence and the table. Do not

feed the workpiece into the blade or cut "freehand"

in any way.

Unrestrained or moving workpieces could be thrown at

high speeds, causing injury.

d) Push the saw through the workpiece. Do not pull

the saw through the workpiece. To make a cut, raise

the saw head and pull it out over the workpiece

without cutting, start the motor, press the saw head

down and push the saw through the workpiece.

Cutting on the pull stroke is likely to cause the saw blade

to climb on top of the workpiece and violently throw the

blade assembly towards the operator.

e) Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e. holding

the workpiece to the right of the saw blade with your left

hand or vice versa is very dangerous.

f) Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning.

The proximity of the spinning saw blade to your hand

may not be obvious and you may be seriously injured.

g) Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always make

certain that there is no gap between the workpiece,

fence and table along the line of the cut.

Bent or warped workpieces can twist or shift and may

cause binding on tile spinning saw blade while cutting.

There should be no nails or foreign objects in the

workpiece.

h) Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the workpiece.

Small debris or loose pieces of wood or other objects

that contact the revolving blade can be thrown with high

speed.

i) Cut only one workpiece at a time.

Stacked multiple workpieces cannot be adequately

clamped or braced and may bind on the blade or shift

during cutting.

j) Ensure the miter saw is mounted or placed on a

level, ﬁ rm work surface before use.

A level and ﬁ rm work surface reduces the risk of the miter

saw becoming unstable.

k) Plan your work. Every time you change the bevel or

miter angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will

not interfere with the blade or the guarding system.

Without turning the tool “ON” and with no workpiece

on the table, move the saw blade through a complete

simulated cut to assure there will be no interference or

danger of cutting the fence.

I) Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or

longer than the table top.

Workpieces longer or wider than the miter saw table

can tip if not securely supported. If the cut-oﬀ piece or

workpiece tips, it can lift the lower guard or be thrown by

the spinning blade.

m) Do not use another person as a substitute for a

table extension or as additional support.

Unstable support for the workpiece can cause the

blade to bind or the workpiece to shift during the cutting

operation pulling you and the helper into the spinning

blade.

n) The cut-oﬀ piece must not be jammed or pressed

by any means against the spinning saw blade.

If conﬁ ned, i.e. using length stops, the cut-oﬀ piece could

get wedged against the blade and thrown violently.

o) Always use a clamp or a ﬁ xture designed to properly

support round material such as rods or tubing.

Rods have a tendency to roll while being cut, causing the

blade to "bite" and pull the work with your hand into the

blade.

p) Let the blade reach full speed before contacting the

workpiece.

This will reduce the risk of the workpiece being thrown.

q) If the workpiece or blade becomes jammed, turn the

miter saw oﬀ . Wait for all moving parts to stop and

disconnect the plug from the power source and/

or remove the battery pack. Then work to free the

jammed material.

Continued sawing with a jammed workpiece could cause

lass of control or damage to the miter saw.

r) After ﬁ nishing the cut, release the switch, hold

the saw head down and wait for the blade to stop

before removing the cut-oﬀ piece.

Reaching with your hand near the coasting blade is

dangerous.

s) Hold the handle ﬁ rmly when making an incomplete

cut or when releasing the switch before the saw

head is completely in the down position.

The braking action of the saw may cause the saw head

to be suddenly pulled downward, causing a risk of injury.

00BookC12RSH2.indb3300BookC12RSH2.indb33 2021/11/0912:16:172021/11/0912:16:17

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki C12RSH2 in the language / languages: All languages as an attachment in your email.

The manual is 9.45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hikoki C12RSH2 Manual

Product: