168668
20
Zoom out
Zoom in
Previous page
1/28
Next page
SPEAKER OUTPUT
+
CH 1 CH 2
+ MONO BRIDGED –
+ +
CH 3 CH 4
+ MONO BRIDGED –
+
e
13
021586
FUSE
LOGO
BADGE
BLUE
WHITE
POWER INPUT
+
CH 5
GND BATT +12VREM
5-CHANNEL AMPLIFIER: ZXi8805
20
Interconnetion example: 3-Way-Active-System and Subwoofer
Connect the stereo RCA output of the headunit
with LINE INPUTS CH1/2 of the amplifier.
Low-/Mid-
Speaker
2 – 8 Ohms
Low-/Mid-
Speaker
2 – 8 Ohms
CH 3
CH 4
LINE INPUT
CH 1
CH 2
CH 5
LEVEL HI PASS
6V 0. 2V
50Hz
150Hz
BASS BOOST LEVEL
0dB 10dB 6V 0.2V
50Hz 4kHz
LOW PASS
30Hz 150Hz
X-OVER
CH 1/2
HP
FULL
REMOTE
HI PASS LOW PASS
HP FULL BP
X-OVER
CH 3/4
LEVEL
6V 0.2V250Hz 4kHz
CH 5
POWER
PROTECT
MODE
4 CH 5 CH2 CH
R L
Tweeter
2 – 8 Ohms
Tweeter
2 – 8 Ohms
Subwoofer
2 – 8 Ohms
INTERCONNECTION
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT CH1/2 of the amplifier with appropriate high-value RCA
cables.
• Connect the tweeters with SPEAKER OUTPUT + CH1 - / + CH2 -.
• Connect the low-/mid-speakers with SPEAKER OUTPUT + CH3 - / + CH4 -.
• Connect the subwoofer with SPEAKER OUTPUT + CH5 -.
• Ensure by any means, that the total impedance load of all speakers is not lower than 2 ohms. Too low impedance cause high temperature
and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
MODE SWITCH
• Select the 2CH position on the MODE switch.
CROSSOVER SETTINGS CH1/2 (Tweeter)
• You must set the X-OVER switch to the HP Position (Highpass Mode) to avoid any damage by lower frequencies on the speakers.
The cut-off frequency is adjustable with the HI PASS controller and should be set between 2500Hz to 4000Hz, depending on the size
of the speakers.
CROSSOVER SETTINGS CH3/4 (Low-/Mid-Speaker)
• You must set the X-OVER switch to the BP Position (Bandpass Mode) to avoid any damage by lower frequencies on the speakers.
The lower cut-off frequency is adjustable with the HI PASS controller and should be set between 60Hz to 150Hz. The higher cut-off
frequency is adjustable with the LOW PASS controller and should be set between 1800Hz to 3800Hz, depending on the size of the
speakers.
LEVEL CONTROLLER CH1/2 & CH3/4 & CH5
• Turn the LEVEL controller of the amplifier to the 6V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
BASS BOOST CONTROLLER CH5
• The BASS BOOST controller is continuously adjustable from 0dB bis +10dB.
LOW PASS CONTROLLER CH5
• The LOW PASS controller is for the adjustment of the Cut-Off-Frequency, which should be between 60Hz and 100Hz, depending on
the size of the subwoofer.
BASS REMOTE CH5
The enclosed BASS REMOTE Controller adjusts the bass-level on CH5 e.g. from the driver’s seat.
Please use only the enclosed bass remote controller and cable.
Connect the bass
remote controller and
the remote terminal on
the amplifier with the
enclosed cable.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics zxi8805 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics zxi8805 in the language / languages: English, German as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info