168668
18
Zoom out
Zoom in
Previous page
1/28
Next page
5-CHANNEL AMPLIFIER: ZXi8805
18
FUNCTIONS AND OPERATIONAL CONTROLS
1
3
The REMOTE port is for the cable of the enclosed bass remote controller and only to use in the LP/BP mode. With this bass
remote controller, you are able to adjust the bass level e.g. from the driver’s seat. Please use only the enclosed bass remote
controller and cable.
1
4
The LOW PASS CH3/4 and CH5 controllers adjust the cut-off point of the frequency range to above for the regarding channel
pair. The cut-off frequency is continuously adjustable, on Channel 3/4 from 250 Hz to 4kHz and on Channel 5 from 30 Hz to
150 Hz.
5
The BASS BOOST CH5 controller adjust the bass boost enhancement continuously from 0dB to +10dB.
6
The HI PASS CH1/2 and CH3/4 controllers adjust the cut-off point of the frequency range to below for the regarding channel
pair (Channel 1/2 or Channel 3/4). The cut-off frequency is continuously adjustable, on Channel 1/2 from 50Hz to 4kHz, on
Channel 3/4 from 50Hz to 150Hz.
7
The LEVEL CH1/2, CH3/4 and CH5 controllers adjust the input sensitivity of the amplifier to align the audio signal of the head
unit for the regarding channel pair (Channel 1/2, Channel 3/4 or Channel 5). The input sensitivity is adjustable from 6 to 0.2
Volts.
8
POWER/PROTECT
If the POWER LED lights up, the amplifier is ready for operation.
If the PROTECT LED lights up, a malfunction is indicated. Attend in this case the chapter TROUBLE SHOOTING.
The LINE INPUT RCA jacks must be connected with the RCA output jacks of the headunit.
1
2
The CH1/2 and CH3/4 X-OVER switch selects the required operation mode of the amplifier on the regarding channel pair
(Channel 1/2 or Channel 3/4).
Position HP: Highpass mode (The higher frequencies will be eliminated. Adjustable by the highpass controller).
Position FULL: Fullrange mode (The whole frequencies will be amplified).
Position BP: The HI PASS controller works in this operation mode as subsonicfilter and eliminates the lower frequencies
(Bandpass-Mode).
9
The MODE switch must be in 2CH position, if you connect only one RCA stereo audio cable with the CH1/2 line inputs.
Select the position 4CH, if you connect two RCA stereo audio cables on the CH1/2 and CH3/4 line inputs. Select the position
5CH, if you connect three RCA stereo audio cables with the CH1/2, CH3/4 and CH5 line.
Do not connect loudspeaker cables with the vehicle’s chassis. Always ensure the correct polarity
of all connections. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
REFERENCE NOTE
1 42 5 6 7 8 93
CH 3
CH 4
LINE INPUT
CH 1
CH 2
CH 5
LEVEL HI PASS
6V 0.2V
50Hz
150Hz
BASS BOOST LEVEL
0dB 10dB 6V 0.2V
50Hz 4kHz
LOW PASS
30Hz 150Hz
X-OVER
CH 1/2
HP
FULL
REMOTE
HI PASS LOW PASS
HP FULL BP
X-OVER
CH 3/4
LEVEL
6V 0.2V250Hz 4kHz
CH 5
POWER
PROTECT
MODE
4 CH 5 CH2 CH
2 4 7
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics zxi8805 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics zxi8805 in the language / languages: English, German as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info