700150

Hifonics X4-Andromeda Manual

22
Zoom out
Zoom in
Previous page
1/28
Next page
22
OPERATING INSTRUCTIONS
WHITE
BLUE
BATT +12V
GND
REM
FUSE
POWER INPUT
LOGO BADGE
SPEAKER OUTPUT
MONO BRIDGED
– CH4 + – CH3 +
MONO BRIDGED
– CH2 + – CH1 +
REMOTE
CH1
CH2
CH3
CH4
LINE INPUTS
CH1/2
CH3/4
BALANCED
INPUTS
STEREO
MONO
12dB
24dB
INPUT MODE
4CH 2CH
LOW PASS
LOW PASS
HIGH PASS
HIGH PASS
X-OVER MODE CH1/2
X-OVER MODE CH3/4
LP/BP FULL HP
LP/BP FULL HP
POWER
PROTECT
L
R
BASS BOOST
BASS BOOST
LEVEL
LEVEL
CH1/2 CH1/2
CH3/4 CH3/4
LINE OUTPUT
SUMMED CH1/2/3/4
FULL RANGE
INTERCONNECTION
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT CH1/2 of the amplifier with appropriate high-value RCA
cables.
• Connect the tweeters with SPEAKER OUTPUT + CH1 - / + CH2 -.
Ensure that the total impedance load of each speaker is not lower than 2 ohms.
• Connect the low-/mid-speakers with SPEAKER OUTPUT + CH3 - / + CH4 -.
Ensure that the total impedance load of each speaker is not lower than 2 ohms.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
INPUT MODE SWITCH
• Select the 2CH position on the INPUT MODE switch.
CROSSOVER SETTINGS CH1/2 (Tweeter)
• You must set the X-OVER switch to the HP Position (Highpass Mode) to avoid any damage by lower frequencies on the speakers.
The cut-off frequency is adjustable with the HI PASS controller and should be set between 2500Hz to 4000Hz, depending on the size
of the speakers.
IMPORTANT NOTE:Do not use the tweeter in any circumstances in full range mode (FULL) or do not replay a music signal without
checking the correct settings before. Turn before starting the LEVEL controller to the 6V position, then adjust the X-OVER switch
CH1/2 to position HP and set the controller HIGH PASS to the right to the 4 kHz position. The tweeter can be irreparably damaged
by already a very low volume levels without a properly adjusted crossover setting .
CROSSOVER SETTINGS CH3/4 (Low-/Mid-Speaker)
• You must set the X-OVER switch to the BP Position (Bandpass Mode) to avoid any damage by lower frequencies on the speakers.
The lower cut-off frequency is adjustable with the HI PASS controller and should be set between 60Hz to 150Hz. The higher cut-off
frequency is adjustable with the LOW PASS controller and should be set between 1800Hz to 3800Hz, depending on the size of the
speakers.
LEVEL CONTROLLER CH1/2 & CH3/4
• Turn the LEVEL controller of the amplifier to the 9V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
INTERCONNECTION EXAMPLE: 2-way Active System
Connect the stereo RCA output of the headunit with
LINE INPUTS CH1/2 of the amplifier.
Low-/Mid-
Speaker
1 – 8 Ohms
Low-/Mid-
Speaker
1 – 8 Ohms
L R
Tweeter
1 – 8 Ohms
Tweeter
1 – 8 Ohms
Schalterstellung CH3/4 = LP/BP
Schalterstellung CH1/2 = HP
Schalterstellung 2CH
STEREO 12dB
Do not connect loudspeaker cables with the vehicle’s chassis. Always ensure the correct polarity
of all connections. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
REFERENCE NOTE
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics X4-Andromeda at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics X4-Andromeda in the language / languages: English, German as an attachment in your email.

The manual is 3,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info