700154
18
Zoom out
Zoom in
Previous page
1/28
Next page
ENG|INSTALLATION INSTRUCTIONS
18
ELECTRICAL INTERCONNECTION
GND
Connect this GROUND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be as short
as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable
and safe electric connection to the negative “–”pole of the battery. Check this ground wire from the battery to the ground point if
possible and enforce it, if required. Use a ground wire with a sufficient cross section (at least 20 mm
2
) and the same size like the
plus (+12V) power supply wire.
REM
Connect the turn-on signal (e.g. automatic antenna) or the turn-on remote signal of your headunit with the REM-terminal of the
amplifier. Use therefor a suitable cable with a sufficient cross section (0,5 mm
2
). Thereby the amplifier will turn on or off automatically
with your headunit.
If your headunit doesn’t provide a separate remote turn on wire and has no pre-amplifier low level RCA outputs, please refer to
the section AUTO TURN ON on the following page.
+12V
Connect the +12V-terminal with the +12V pole of the vehicle’s battery. Use therefor a suitable cable with a sufficient cross section
(at least 20mm
2
) and install a additional in-line fuse. For safety reasons the distance between the fuseblock and the battery must
be shorter than 30 cm. Do not install the fuse into the fuseblock until the installation is accomplished.
LOGO BADGE
This switch changes the illumination color of the upper logo badge (blue or white). Follow by any means the directives of your
national road traffic regulations.
FUSE
The inserted fuses protect the amplifier from shorts and capacity overload. Replace damaged fuses only with equal fuses with
the same fuse rating (check the specifications).
1
2
3
4
BEFORE THE CONNECTION
For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Attend the sufficient
profile section (at least 20 mm
2
), the suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and
remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection. Make sure that all screws are
fixed tight after the installation, because loosely connections may cause malfunctions, insufficient power supply or interferences.
5
421 3 5
Installation of RCA/Audio signal cables and power supply.
Ensure while installation not to lead the audio cables between the headunit and the amplifier together with the power supply wires
on the same side of the vehicle. The best is a areal separated installation in the left and right cable channel of the vehicle. Therewith
a overlap of interferences on the audio signal will be avoided. This stands also for the equipped bass-remote wire, which should be
installed not together with the power supply wires, but rather with the audio signal cables.
REFERENCE NOTE
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics TSi1500-I at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics TSi1500-I in the language / languages: English, German as an attachment in your email.

The manual is 2,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info