700160

Hifonics Triton II Manual

16
Zoom out
Zoom in
Previous page
1/24
Next page
ENG|INSTALLATION INSTRUCTIONS
16
GND
Connect this GROUND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be as short
as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable
and safe electric connection to the negative “–”pole of the battery. Check this ground wire from the battery to the ground point if
possible and enforce it, if required. Use a ground wire with a sufficient cross section (at least 16 mm
2
) and the same size like the
plus (+12V) power supply wire.
REM
Connect the turn-on signal (e.g. automatic antenna) or the turn-on remote signal of your headunit with the REM-terminal of the
amplifier. Use therefor a suitable cable with a sufficient cross section (0,5 mm
2
). Thereby the amplifier will turn on or off automatically
with your headunit.
+12V
Connect the +12V-terminal with the +12V pole of the vehicle’s battery. Use therefor a suitable cable with a sufficient cross section
(at least 16mm
2
) and install a additional in-line fuse. For safety reasons the distance between the fuseblock and the battery must
be shorter than 30 cm. Do not install the fuse into the fuseblock until the installation is accomplished.
FUSE
The inserted fuses protect the amplifier from shorts and capacity overload. Replace damaged fuses only with equal fuses with
the same fuse rating (check the specifications).
AUTO TURN ON & INPUT LEVEL MODE
If your headunit doesn’t provide a separate remote turn on wire (like described under #2) and has no pre-amplifier low level RCA
outputs, follow these instructions:
Push the AUTO TURN ON button to position ON to activate the auto turn on function. This function only works, if the push button
INPUT LEVEL MODE is in HI position and highlevel inputs (speaker outputs from the headunit) are connected at the LINE IN.
Please check the regarding notes below.
The amplifier detects now by the so called ”DC Offset” (a voltage increase to 6 volts on the high level speaker outputs) if the
headunit is turned on and the amplifier turns automatically on. As soon as the headunit is turned off, the amplifier shuts down
automatically after approx.one minute.
NOTE: The AUTO TURN ON usually works with 90% of all headunits, because they are equipped with the ”High Power” outputs.
Only with a few older headunits the AUTO TURN ON function is not applicable.
The port of the remote connector of the amplifier (#2, REM) can now be used also to turn on additional other amplifiers. Connect
the REM ports of the amplifiers and ensure, that the other amplifier’s AUTO TURN ON function is deactivated.
ELECTRICAL INTERCONNECTION
1
2
3
4
BEFORE THE CONNECTION
For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Attend the sufficient
profile section (at least 16 mm
2
), the suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and
remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection. Make sure that all screws are
fixed tight after the installation, because loosely connections may cause malfunctions, insufficient power supply or interferences.
421 3
5
5
+
–
To connect the high level speaker cables of the headunit
follow these instructions:
Crimp and solder the ends of the loudspeaker cables of the
headunit with common RCA connectors (separately available)
and connect them with LINE IN of the amplifier.
You can simplify the installation, if you use the separately available
hi-to-lo adaptors HF-HLA from HiFonics (see page 21).
Shield
To the LINE IN on the Amp
Speaker Cables
Core Conductor
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics Triton II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics Triton II in the language / languages: English, German as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info