700160

Hifonics Triton II Manual

22
Zoom out
Zoom in
Previous page
1/24
Next page
Malfunction: no function
Reason: Remedy:
1. The power supply connection of the device is not correct. Recheck
2. The cables have no mechanical or electrical contact. Recheck
3. The remote turn-on connection from the headunit to the amplifier is not correct. Recheck
4. The high level inputs (from the head unit) are not connected correct and AUTO TURN ON is activated. See page 16 and 21
5. By using the AUTO TURN ON function the button INPUT LEVEL MODE is not in HI position and the button Set buttons to HI and ON
AUTO TURN ON not in ON position or the headunit is not equipped with ”High Power” outputs. See page 16
6. Defective Fuses. In case of replacing the fuses, attend by any means the correct fuse rating. Replace Fuses
Malfunction: no signal on loudspeakers, but power LED lights up
Reason: Remedy:
1. The connection of the speakers or the RCA audio cables is not correct. Recheck
2. The speaker cables or the RCA audio cables are defective. Replace cables
3. The loudspeakers are defective. Replace speakers
4. High pass controller (Subsonic Mode) in LP/BP operation is adjusted to high. Turn down controller
5. No signal from headunit. Check headunit settings
Malfunction: one or more channels/controllers are without function / faulty stereo stage
Reason: Remedy:
1. The balance or fader controller of the headunit is not in the zero-position. Turn to zero-position
2. The connection of the speakers is not correct. Recheck
3. The loudspeakers are defective. Replace speakers
4. High pass controller in LP/BP operation is adjusted to high. Turn down controller
Malfunction: distortions on the loudspeaker’s signal
Reason: Remedy:
1. The loudspeakers are overloaded. Turn down the level
Turn down the level on the headunit
Switch off loudness on the headunit
Reset bass EQ on the headunit
Malfunction: No bass or stereo sound
Reason: Remedy:
1. Interchange of loudspeaker cable polarity positive (+) and negative (-). Reconnect
2. The RCA audio cables are loose or defective. Reconnect or replacing the cables
Malfunction: amplifier runs into protection mode (red protection LED lights up)
Reason: Remedy:
1. Short circuit on the loudspeakers or cables. Reconnect
2. Overheated by too low speaker impedance. Choose a higher impedance
Use a new speaker setup
3. Insufficient air circulation by a inappropriate mounting position of the amplifier. Change the mounting position
Ensure air circulation
4. Overloaded by insufficient power supply (too thin profile section on the power cables). Use a bigger profile section
Malfunction: hiss or white noise on the loudspeaker’s signal
Reason: Remedy:
1. The level controllers are turned up. Turn down the level
2. The treble controller on the headunit is turned up. Turn down the level on the headunit
3. The speaker cables or the RCA audio cables are defective. Replacing the cables
4. The hissing is caused by the headunit. Check the headunit
22
ENG|TROUBLE SHOOTING
… 22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics Triton II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics Triton II in the language / languages: English, German as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info