700159
20
Zoom out
Zoom in
Previous page
1/24
Next page
12
20
ENG|OPERATIONAL INSTRUCTIONS
INTERCONNECTION EXAMPLE HIGHPASS/FULLRANGE: 1 x Speaker System
INTERCONNECTION AMPLIFIER 1
Connect the RCA lineout L of the headunit with the RCA jacks LINE IN R & L of the amplifier with appropriate high-value RCA cables
and a Y-connector (1F/2M) to split the signal.
• Connect the speaker (left) with the speaker outputs (SPEAKER OUTPUTS + and - of the same socket) by using appropriate wires.
Ensure by any means, that the total impedance load of all speakers is not lower than 2 ohms. Too low impedance cause high temperature
and will shut down the amplifier operation.
Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
INTERCONNECTION AMPLIFIER 2
Connect the RCA lineout R of the headunit with the RCA jacks LINE IN R & L of the amplifier with appropriate high-value RCA cables
and a Y-connector (1F/2M) to split the signal.
• Connect the speaker (right) with the speaker outputs (SPEAKER OUTPUTS + and - of the same socket) by using appropriate wires.
Ensure by any means, that the total impedance load of all speakers is not lower than 2 ohms. Too low impedance cause high temperature
and will shut down the amplifier operation.
Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
CROSSOVER SETTINGS AMPLIFIER 1 & 2 (Please use the same settings for both amplifiers)
• By using bigger speakers (more than 20cm) you can set the X-OVER MODE switch to the FULL position (Full Range Signal).
• By using smaller speakers (8.7cm - 16cm) you must set the X-OVER MODE switch to the HPF Position (Highpass Mode) to avoid
any damage by lower frequencies on the speakers. The cut-off frequency is adjustable with the HPF controller and should be set between
60Hz to 150Hz, depending on the size of the speakers.
The LPF Controller is not in use in this interconnecting example.
LEVEL CONTROLLER AMPLIFIER 1 & 2 (Please use the same settings for both amplifiers)
• Turn the LEVEL controller of the amplifier to the MIN. position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
BOOST CONTROLLER AMPLIFIER 1 & 2
• The BOOST controller must be turned to 0 dB position in this interconnecting example.
REMOTE BASS LEVEL CONTROLLER BLC-TR AMPLIFIER 1 & 2
The enclosed remote BASS LEVEL Controller is not in use in this interconnecting example.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics Triton I at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics Triton I in the language / languages: English, German as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info