505731
6
Zoom out
Zoom in
Previous page
1/18
Next page
CH1/2 CH3/4 REMOTE HI PASS CH1/2 X-OVER LOW PASS BASS EQ LEVEL POWER LINE OUTPUT
10Hz 1.5kHz 30Hz 150Hz 0dB 10dB 6.0V 0.2V
10Hz 1.5kHz 30Hz 150Hz 0dB 10dB 6.0V 0.2V
LINE INPUT MODE HI PASS CH3/4 X-OVER LOW PASS BASS EQ LEVEL
PROTECT
R
L
R
L
2CH 4CH
HI FULL LP/BP
HI FULL LP/BP
CH1/2 CH3/4 REMOTE HI PASS CH1/2 X-OVER LOW PASS BASS EQ LEVEL POWER LINE OUTPUT
10Hz 1.5kHz 30Hz 150Hz 0dB 10dB 6.0V 0.2V
10Hz 1.5kHz 30Hz 150Hz 0dB 10dB 6.0V 0.2V
LINE INPUT MODE HI PASS CH3/4 X-OVER LOW PASS BASS EQ LEVEL
PROTECT
R
L
R
L
2CH 4CH
HI FULL LP/BP
HI FULL LP/BP
4
BRX320.4 / BRX640.4 / BRX1200.4 4-CHANNEL AMPLIFIER APPLICATIONS
POWER INPUT
GND REM BATT+12V
CH 1/2 SPEAKER OUTPUT CH 3/4
RIGHT LEFT RIGHT LEFT
- + - + - + - +
BRIDGED BRIDGED
FUSE
POWER INPUT
GND REM BATT+12V
CH 1/2 SPEAKER OUTPUT CH 3/4
RIGHT LEFT RIGHT LEFT
- + - + - + - +
BRIDGED BRIDGED
FUSE
4 CHANNEL FULL RANGE SYSTEM
2 or 3 CHANNEL SYSTEM
- HI PASS: N/A
Here we show how to use the 4 channel amplifiers as straightforward discrete 4
- LOW PASS: N/A
channel full range units.
Interconnect cable checklist:
Channels 1 / 2 & 3 / 4:
- Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables.
- HI PASS: N/A
- LOW PASS: N/A
Switch setting checklist:
- 1/2CH X-OVER: FULL
Level control checklist:
- 3/4CH X-OVER: FULL
- Refer to the section “Setting up systems after installation for best performance”
Minimum final loudspeaker impedances:
Crossover frequency control checklist:
- 2 ohm per channel.
Channels 1/2:
Crossover frequency control checklist:
Here we show how to use the 4 channel amplifiers as a 3 channel unit by taking
Channels 1/2:
advantage of the mono bridging capability of all Hifonics amplifiers.
- HI PASS: N/A
The following example shows how to create a 3 channel system by mono
- LOW PASS: 11 o’clock
bridging channel pair 1/2. In order to create a 2 channel system, simply follow
the example to also mono bridge channel pair 3/4.
Channels 3/4:
- HI PASS: N/A
Interconnect cable checklist:
- LPF: N/A
- If supplying the unit with mono signal on ch 1 / 2 stereo signal to ch 3 / 4, you will
switch MODE to 4CH.
TIP: If you are using the mono sub bass output of an active crossover, there is
- If you only have 1 set of RCA outputs from your headunit, you can simply
nothing wrong with switching in the low pass filter in these amplifiers for a
connect those to the inputs for ch 1/2 and switch the MODE to 2ch. The amplifier
steeper low pass rolloff.
will automatically route the signal to channels 3/4.
Important: Do not be tempted to connect the hot, or positive outputs, from any
Level control checklist:
source together to obtain a mono signal, as this could very well damage the
- Refer to the section “Setting up systems after installation for best performance”
output stage of that source.
- It is necessary to feed the SAME signal to both left and right inputs via a Y-
Minimum final loudspeaker impedances:
adapter RCA cable.
- 2 ohm per channel in stereo mode.
- Connect the mono speaker positive terminal to the LEFT +, and its negative
- 4 ohm mono bridged.
terminal to RIGHT - as shown.
Switch setting checklist:
- 1/2CH X-OVER: LP
- 3/4CH X-OVER: FULL
STEREO LINE INPUT
MONO LINE INPUT
(Unless using procedure
listed above for 2ch)
BRUTUS
BRUTUS
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics Brutus BRX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics Brutus BRX in the language / languages: English as an attachment in your email.

The manual is 6,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info