741731

Hendi CM1089A Manual

256
Zoom out
Zoom in
Previous page
1/264
Next page
English - 16
English - 17
MULTI - STAGE COOKING.
1. Upon pressing the PROG button, the oven will enter
Program mode. The display will be cleared.
2. Using the Number buttons, enter the program number from
1 to 20.
3. Then, press the Power Level button to select power.
By pressing the Power Level button repeatedly, you can
select the power level - HI, MED, or LOW.
4. Use the Number buttons to enter the cooking time. You can
set a time from one second to 30 minutes. To set a time
over one minute, enter the seconds as well.
For example, to set 10 minutes, enter 1, 0, 0, 0.
5. Repeat step 3 and 4 for II or III stage memory
proggramming.
6. Press the PROG button to complete setting the memory.
The display will show ‘0’.
The maxium allowable cooking time is 30 min. If the time exceed 30 min, the display
will show “E3”, then press Stop/Cancel button and repeat the steps.
USING MEMORY PROGRAMMING.
Press the Number buttons to select user-programmed memory functions (please refer to
memory programming) from 1 to 20.
Press the Start button.
IftheDEFROSTfunctionisincludedinSTAGECOOKING,itworksatrst.
If you want to change program, just reset MEMORY PROGRAMMING.
USING THE CHECK BUTTON
ConrmingthecookingtimeandPowerLevelineachmemoryprogram.
1. ClearalloperationsbypressingtheStop/Cancel button.
Press the CheckbuttontoenterCheckmode.
2. Using the Number buttons, enter the program number from
1 to 20.
For example, suppose you press ‘5’, for the Memory
Program 5 which is HI Power Level, I Stage cooking with a
time of 6 minutes and 30 seconds, 6:30.
First, ‘5’ will be displayed. but will change to show the
3. After one second, the display will clear automatically.
If you want to check other Memory Programs, just enter the
Memory Program numbers.
4. Press the Stop/Cancel bottontoexittheCheckmode.
ReadingeachMemoryProgram’sCycleCounter
1. ClearalloperationsbypressingtheStop/Cancel button.
Press the CheckbuttontoenterCheckmode.
2. Press the Start button, and then press any Number button,
from 1 to 20, and the number of cycles for that particular
Memory Program will be displayed. The cycle count is
displayed in units of 10.
For example, if Memory Program 5 has been used
100times, the display will show ‘10’.
3. After one second, the display will clear automatically. If
you want to check other Memory Programs, just enter the
Memory Program numbers.
4. Press the Stop/Cancel buttontoexittheCheckingmode.
As the display uses units of 10, the cycle counts are approximate. The cycle count
displayed increases every ten cycles.
For example, if the cycle count were 90-99, “9” would be displayed, The “9” would
change to “10” on the 100th cycle. The cycle counter function has a limit of 99,990
cycles. Once that number is exceeded, the cycle counter will automatically clear and
start again from “0”.
CM1089A_XEU_DE68-03310E-03_EN_160629.indd 16 2016-06-29 �� 2:56:15
… 256 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hendi CM1089A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hendi CM1089A in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 13,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info