741086
7
Zoom out
Zoom in
Previous page
1/20
Next page
7
EN
CHAPTER 3. FUNCTIONING
3.1. CONTROL DEVICES
The equipment is provided with the following control devices:
On the front:
Start (1)
Stop (0)
Foot pedal (2) (Manual operation mode – use foot-pedal in this mode)
3.2. FUNCTIONAL VERIFICATION
After electrical connection to the socket, the equipment is ready for the functional verification.
Start: press the button (1), the equipment starts.
Stop: press the button (0), the equipment stops.
Start the equipment without dough and let it run for 1 minute to make sure it is functioning properly.
CHAPTER 4. USE
Before every working-cycle always make sure that
the equipment is perfectly cleaned, in particular those
surfaces that get in touch with the dough. If neces-
sary clean the equipment as indicated in the follow-
ing chapter.
4.1. USE OF THE EQUIPMENT
TO START
Push the button in position 1; the equipment starts
the two rollers and it is now ready to be used.
Before introducing the dough previously left to rise
(at least 6 to 8 hours) open the rollers using the han-
dle (in position 3-4).The dough needs to be floured
and squashed slightly to get through the rollers.
When the dough comes out it will be in an oval shape
and you will notice reduction of thickness. Towards
the end of this step, you need to support with your
hand the dough until it come out completely. At this
stage rotate the dough in a transversal way of about
90° and put it trough the rollers once more (in posi-
tion 1-2). You will finally get an almost perfect disk
shape dough that can be easily enhanced with few
finishing touches by hand.
TO STOP
Press the button (0).
4.2. USAGE OF THE FOOT PEDAL (OPTION)
The foot pedal will only be installed by request of
customer.
The foot pedal is a convenient alternative to the start
and stop button and it makes possible to keep the
equipment on during the time needed.
This pedal is connected to the equipment by intro-
ducing the plug on the side if the equipment.
TO START
Pressing the button (2), the equipment does not start but it is on hold.
Pressing slowly the foot pedal, rollers start moving and the equipment is ready for use.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hendi 226599 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 226599 in the language / languages: English, Polish as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info