741172
8
Zoom out
Zoom in
Previous page
1/92
Next page
8
EN
Cleaning and Maintenance
Attention: Always unplug the appliance from the electrical power outlet and let it cool down completely before
cleaning and disassembly the blending part (7).
Cleaning
Remove all obstacles near the blade.
Place the blending arm and the bell in a suitable
container with clean water and switch on for a
few seconds. Never immerse the shaft above the
Max. mark.
Never immerse the motor unit or the handle in
water; clean with a damp cloth or a sponge.
WARNING: Always dry the blades thoroughly after
cleaning to avoid rust spotting.
Recommended cleaning procedure:
Parts How to clean Frequency
Main unit with motor
(10)
Never immerse this part into water or other liquids.
Using a damp cloth with some detergent and water, rinse, sanitize and
dry thoroughly.
Clean after each
use
Blending part (7) Clean it with warm water and some mild detergent. Do not submerge
the Detachable blending part (7) above the Max. mark.
Dry all parts before using again.
Blade (8) Warning! Risk of injury! Take great care when cleaning the blades.
Clean it with warm water and some mild detergent.
Dry it thoroughly after cleaning.
Storage
Before storage, always make sure the appliance
has already been disconnected from the electrical
outlet and cooled down completely.
Store the appliance in a cool, clean and dry place
and keep out of reach of the children.
Troubleshooting
If the appliance does not function properly, please
check the below table for the solution. If you are
still unable to solve the problem, please contact the
supplier/service provider.
Problems Possible causes Possible solution
Appliance does not switch on Power plug is not connected to a
suitable power supply properly.
Check to make sure the power plug is connected
to a suitable electrical outlet properly.
ON/OFF button (1) is not pressed. Press and hold the ON/OFF button (1) to switch on
the appliance.
Abnormal noises while pro-
cessing
The blending part (7) is not con-
nected correctly.
Disassembly and assembly the blending part (7)
again.
Appliance cannot operate Inside overheat devices activates. Let the appliance cool down complete before start
operation again.
Appliance is overheat Overtime operation Release the ON/OFF button and unplug the device,
wait 10 minutes for the motor to cool down.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hendi 222157 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 222157 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 2,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info