741179
10
Zoom out
Zoom in
Previous page
1/88
Next page
10
EN
Troubleshooting
If the machine does not function properly, please check the below table for the solution. If you are still un-
able to solve the problem, please contact the supplier/service provider.
Problems Possible cause Possible solution
The machine does not switch on.
Power plug is not connected properly with
the electrical power outlet.
Make sure the power plug is connected
properly with the electrical power outlet.
The vacuum bag is not vacuum and / or
sealed completely.
Vacuum/ Seal time is not long enough. Set longer Vacuum/Seal time.
The opening of the vacuum bag was not
entirely and properly placed under the
sealing bar (8).
Pack the food in a new bag and place
properly in the chamber so the entire
opening can be sealed. Don’t use bags
that don’t fit the sealing bar.
The sealing bar (8) and the inside vacuum
chamber (9) is not clean enough.
Wipe the surface of the sealing bar (8)
and inside the vacuum chamber (10) to
keep clean, dry and free of debris.
There is some moisture, food particles or
debris on the seal area of the vacuum bag.
Wipe the seal area of the vacuum bag to
make sure it is dry and clean.
Vacuum bag loses vacuum after being
sealed.
Inside the vacuum bag has food with
sharp points to penetrate the bag and
thus air enters into the vacuum bag.
Cut off the sharp points or cover it before
packing.
Some food can release gases also food
can release gases due to food spoilage.
Blanch or frozen the food properly before
packaging. Discard the food if in doubt.
Error codes display
Error codes shown on the digital display
(F)
Possible cause Possible solution
E01 - The lid (1) is not properly closed.
- Oil pump is defective.
- Machine internal system is defective.
- The lid (1) is not properly closed.
- Contact the supplier.
- Contact the supplier.
LP - Machine lost electrical power supply
suddenly during operation.
- Check the electrical power supply.
Technical specification
Item no. 201442
Operating voltage and frequency 220-240V~ 50 / 60 Hz
Rated input power 1100W
Protection class Class I
Max vacuum bag width 410 mm
Pump capacity 333,3 L/min
Pressure -29,9” Hg / -1012 mbar (± 3%) directly at the pump
-29,8” Hg / -1009 mbar (± 3%) in vacuum chamber
Width of sealing bar 2 x 3,5 mm
Dimension 505 x 567 x (H) 465 mm
Net weight approx. 60kg
Remark: Technical specification is subjected to change without prior notification.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hendi 201442 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 201442 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info