801892

Hayward Aqua Rite Pro LS Manual

32
Zoom out
Zoom in
Previous page
1/100
Next page
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 15 of 16 AquaRite® Pro LS Rev. D
pH Dispense Wiring
A screw terminal block located on the enclosure surface below the transformer is provided for connection to a 230 V
pH related dispensing device (peristaltic pumps). After properly installing and configuring the AQL-CHEM and the pH
dispensing device, the AquaRite Pro LS will turn on the dispensing device when pH correction is required.
230 V pH Dispensing Device
LN
230 V
EP1
EP2
N L
to 230 V
pH Dispensing Device
like peristaltic pump
BROWN
BLUE
Main Power
Supply
TROUBLESHOOTING
The “CHECK SYSTEM” LED will alert you when the AquaRite Pro LS detects any of the following conditions that are
abnormal and require attention for optimal operation of your pool. Press “<“ or “>” to view all of the existing “Check
System” conditions.
• Inspect Cell -- For optimum operation, you will need to inspect the AquaRite Pro LS chlorinator cell approximately
every 3 months and clean the cell if necessary. The AquaRite Pro LS will automatically remind you when it is time and
display “Inspect Cell, + to reset” as part of the rotating Default Menu. Clean the cell (see instructions, page 11) and then
press the “+” button during the “Inspect Cell” display to reset the timer.
• High Salt/Amps -- The AquaRite Pro LS will stop generating chlorine under certain high salt conditions in order to
protect the internal electronics from damage. The only way to lower the salt level is to partially drain the pool and add
fresh water.
• Chlorinator Cell Sensor -- The cell sensor is either an open or short circuit.
• Low Volts -- If the chlorinator cell voltage is too low.
• No Cell Power -- If no chlorinator cell power is detected on the printed circuit board.
• Check Flow Switch -- If the flow switch input is invalid.
• Cell Power Error -- If a chlorinator cell power error is detected on the printed circuit board.
• Cell Missing -- If the chlorinator is enabled but no cell is detected.
• CSM Comm Error -- If Chemistry Sensing is enabled and the Chemistry Sense Module (CSM) is not responding.
• pH Probe Error -- If the CSM indicates that there is a problem with the pH probe.
• pH Low - Check Feeder -- If a pH level of 6.9 or less is detected, check the feeder for proper operation
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hayward Aqua Rite Pro LS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hayward Aqua Rite Pro LS in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info