815496
20
Zoom out
Zoom in
Previous page
1/40
Next page
Harman® • P-Series Owner’s Manual_R16 • 2018 - ___ • 01/2320 8390-044C
STOVE DOES NOT FEED
1. No fuel in hopper.
2. Fireboxdraftmaybetoolowforsensingswitchinfeeder
circuit to operate. Check for closed doors, loose or
missing gasket on doors or hopper lid.
3. Feed motor will not run until the ESP control senses a
certain temperature. Maybe you did not put enough fuel
or starting gel in the burn pot before manually lighting the
re.
4. Restriction in the hopper or feeder. Remove all fuel and
examine.Cleartheobstruction.
5. Feed motor has failed.
PARTIALLY BURNED PELLETS
1. Feed rate too high.
2. Poorairtofuelmixture.(Checkburnpotclean-outcover
andairintake).
3. Burnpotorheatexchangertubesmayneedtobecleaned.
4. Combination of all the above.
5. #6 status blink: A 6 blink control board status indication
is caused by poor or incomplete combustion. The circuit
board has the ability to track the combustion through feed
settings and ESP temperatures. When the control board
has calculated poor or incomplete combustion, it will shut
downtheunit as a safety feature. (Poor or incomplete
combustion is a contributor of creosote which may cause
achimneyre)
A 6 blink status may be caused by several things:
1. Blockedorpartiallyblockedue.
2. Blocked or partially blocked inlet air.
a. Backdraft damper on the inlet pipe may be stuck closed.
b. If outside air is installed, the inlet cover may be blocked.
3. Theairchamberundertheburnpotmaybelledwithnes
and small bits of ash.
4. Theholesintheburnpotmaybegettinglledwithashor
carbon buildup.
5. Combustion blower fan blades may need cleaned.
6. Fuel restrictions as noted above.
SMOKE SMELL
Follow venting manufacturer’s recommendations for sealing
pipejoints.Theexhaustventistheonlypartofthesystem
that is under positive pressure.
FIRE HAS GONE OUT- Check for status light.
1. No fuel in hopper.
2. Draftistoolow,blockedue.
3. Somethingisrestrictingfuelow.
4. Hopper lid not closed properly.
5. Feed motor or combustion blower has failed.
SMOKE IS VISIBLE COMING OUT OF VENT
1. Air-fuelratioistoorich.
a. Feed rate too high.
b. Draft too low caused by a gasket leak.
LOW HEAT OUTPUT
1. Feed rate too low
2. Draft too low because of gasket leak.
3. Poor quality or damp pellets
4. Combination of 1 and 2.
HELPFUL HINTS
1. Cleaning Burn Pot
Whenever your stove is not burning, take the opportunity to
scrape the burn pot to remove carbon buildup. A vacuum
cleaner is handy to remove the residue. Be sure the stove
is cold if you use a vacuum.
Carbonbuildupcanbescrapedloosewiththereburning
using the special tool provided with your stove. Scrape the
oorandsidesoftheburnpot.Thecarbonwillbepushedout
by the incoming fuel. Always wear gloves to do this.
2. Removing Ashes
TurntheTempDialtonumber1approximately30minutes
before removing ashes. This will result in a cooler stove and
ash pan.
Maximum Feed Limit settings are not needed in most
cases.Operatinginthenormalrange(#4)isrecommended
whenmaximumheatoutputisnotrequired.TheESPprobe
preventsthestovefrombeingover-red.
Keep the stove free of dust and dirt.
Fuel
TheP-SeriesPelletStoveisapprovedforburninganygrade
ofpelletizedbio-massfuel.
It should be noted, however, that higher ash content will
require more frequent ash removal, scraping of the burn pot,
and may provide less BTU’s per pound.
Themoisturecontentofpelletsmustnotexceed8%.Higher
moisture will rob BTU’s and may not burn properly.
Fuel should not be stored within the stove installation
clearances or within the space required for cleaning and
ash removal.
C. Troubleshooting
Withproperinstallation, operation, and maintenance your appliance will provide yearsoftrouble-freeservice.Ifyoudo
experienceaproblem,thistroubleshootingguidewillassistaqualiedservicepersoninthediagnosisofaproblemandthe
correctiveactiontobetaken.Thistroubleshootingguidecanonlybeusedbyaqualiedservicetechnician.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman P43-C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman P43-C in the language / languages: English as an attachment in your email.

The manual is 8.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman P43-C

Harman P43-C User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info