Manual Harman Kardon RCP2 (page 10 of 24) (English)

502828

Zoom out

Zoom in

1/24

PROGRAMMING THE REMOTE

LED under the reassigned Input Selector will flash

three times and then go out.

Example: To use the CBL/SAT button to operate

a second VCR, first press the

VID 2/CBL/SAT

Input Selector

e and the Mute Button

at the same time until the red light glows under

the

VID 2/CBL/SAT Button e. Press the VCR

Button

e, followed by the three-digit code for the

specific model you wish to control. Finally, press the

VID 2/CBL/SA

T Button

e again.

Resetting the RCP 2’s Memory

As you add components to your home theater system,

occasionally you may wish to totally reprogram the

remote control without the confusion of any commands,

macros or “Punch-Through” programming that you may

have done. To do this, it is possible to reset the RCP 2

to the original factory defaults and command codes by

following these steps. However, once the remote is

reset, all commands or codes that you have entered

will be erased and will need to be reentered:

1. Press any of the

Input Selector Buttons e and

the

“O” Button r at the same time until the

Program/SPL Indicator c begins to flash amber.

2. Press the

“3” Button r three times.

3. The red LED under the

Input Selector e will go

out and the

Program/SPL Indicator c will stop

flashing and turn green.

4. The

Program/SPL Indicator c will remain green

until the RCP 2 is reset. Note that this may take a

while

, depending on how many commands are in the

memor

y and need to be erased.

5. When the

Program/SPL Indicator c goes out,

the RCP 2 has been reset to the factory settings.

Programmed Device Functions

Once the RCP 2 has been programmed for the codes

of other devices

press the appropriate

Input Selector

e to change the remote from controlling the AVR to

controlling the additional product. When you press any

one of the selectors, it will briefly flash in red to indicate

that you have changed the device being controlled.

When operating a device other than the AVR, the con-

trols may not correspond exactly to the function printed

on the remote or button.

Some commands

, such as

the volume control, are the same as they are with the

VR.

Other buttons will change their function so that

they correspond to a secondary label on the remote.

For example, the Sleep and Surround mode selector

buttons also function as the Channel Up and Channel

Down buttons when operating most

TV sets

VCRs or

cable boxes. The Channel Up/Down indication is printed

directly on the remote. For many standard CD players,

cassette decks, VCRs and DVD functions, the standard

function icons are printed on top of the buttons

For some products, however, the function of a particu-

lar button does not follow the command printed on

the remote. In order to see which function a button

controls, consult the Function List tables on pages 11

and 12.

To use those tables, first check the type of

device being controlled (e.g., TV, VCR). Next, look at

the remote control diagram in the figure at right. Note

that each button has a number on it.

o find out what function a particular button has for

a specific device

, find the button number on the

Function List and then look in the column for the device

you are controlling. For example, button number 46

is the Direct button for the AVR, but it is the “Favorite”

button for many cable television boxes and satellite

receivers. Button number 30 is the Digital Selection

button for the AVR, but the Open/Close button for CD

players.

NOTE: The numbers used to describe the button

functions in the diagram on this page for the purposes

of describing how a button operates are a different set

of numbers than those used in the rest of this manual

to describe the button functions for the AVR.

Notes on Using the RCP 2 With Other Devices

• Manufacturers may use different code sets for the

same product category. For that reason, it is impor-

tant that you check to see whether the code set you

have entered operates as many controls as possible.

If it appears that only a few functions operate, check

to see whether another code set will work with more

buttons.

•

When a button is pressed on the RCP

the red

light under the

Input Selector e for the product

being operated should flash briefly. If the Device

Control Selector flashes for some but not all but-

tons for a particular product, it does NOT indicate a

problem with the remote but rather that no function

is programmed for the button being pushed.

10 PROGRAMMING THE REMOTE

RCP 2 Remote OM 10/4/04 4:38 PM Page 12

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon RCP2 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon RCP2 Manual

Product: