Manual Harman Kardon RCP2 (page 8 of 24) (English)

502828

Zoom out

Zoom in

1/24

PROGRAMMING THE REMOTE

3. Press the Input Selector e button chosen and

the

Learn Button at the same time. Hold

these buttons until the

Program/SPL Indica

tor

c flashes amber and the light under the device

selector button turns red. Release the buttons.

Press the button on the RCP 2 that you wish to

program. The

Program/SPL Indicator c will

stop flashing.

Within 5 seconds, press and hold the button on the

original remote that you wish to “teach” into the

RCP 2. When the Program/SPL Indicator c turns

green three times, release the button. The Program

Indicator will then begin to flash amber again.

NOTE: If the Program/SPL Indicator c turns

red during Step 4 or 5,

the programming was not

successful. Repeat the steps to see whether the

code will “take.”

6. Repeat Steps 4 and 5 for each button on the

source remote that you wish to transfer to the

RCP 2 remote.

7. Once all codes have been transferred from the

original source remote to the RCP 2, press the

Learn Button .

8. Repeat Steps 1 through 7 for any additional

remotes you wish to “teach” into the RCP 2.

Erasing Learned Codes

The RCP 2 allows you to remove or erase the code

learned into a single button for a single device, to

remove or erase the code set for all the codes that

have been programmed into specific device buttons

or to erase all commands that have been lear

ned

to all devices.

If you erase a code that is part of a macro, that macro

sequence will no longer operate properly.

o erase a single lear

ned code from within a single

device’s settings, follow these steps:

1. Press and hold both the

Input Selector ef

within which the individual button to be erased has

been programmed and the

Learn Button .

When the red LED

under the

Input Selector tur

red and the

Program/SPL Indicator c flashes

amber, release the buttons.

3. Press and release the

Input Selector ef

again for the device within which the individual

button to be erased has been programmed.

4. Press the

7 Button r four times.

Press and release the individual button for which the

code is to be erased. The

Program/SPL Indicator

c will blink green twice and then retur

n to amber

6. To erase other buttons within the same device, press

them as described in Step 5.

7. When all buttons to be erased have been pressed,

press the

Learn Button to complete the

process.

To erase all codes within a single device, follow these

steps:

1. Press and hold both the

Input Selector ef

for which you wish to erase the codes and the

Learn Button .

2. When the red LED under the

Input Selector turns

red and the

Program/SPL Indicator c flashes

amber, release the buttons.

3. Press and release the

Input Selector ef

again for the device whose codes you wish to erase.

4. Press the

8 Button r four times.

5. The

Program/SPL Indicator c will turn off and

the red light under the

Input Selector will flash on

and off once to indicate that the codes have been

erased.

To erase all codes that have been programmed to all

devices in the remote, follow these steps:

1. Press any

Input Selector ef for which

you wish to erase the codes and also the

Learn

Button

2. When the red LED under the

Input Selector turns

red and the

Program/SPL Indicator c flashes

amber, release the buttons.

3. Press and release the

Input Selector ef

again for the device whose codes you wish to erase

4. Press the

9 Button r four times.

5. The

Program/SPL Indicator c will turn off and

the red light under the

Input Selector will flash on

and off once to indicate that the codes have been

erased.

Macro Programming

Macros enable you to easily repeat frequently used

combinations of commands with the press of a single

button on the RCP 2. Once programmed, a macro will

send out up to 19 different remote codes in a prede

termined sequential order, enabling you to automate

the process of turning on your system, changing

devices

or other common tasks. The RCP 2 can store

up to five separate macro command sequences: one

that is associated with the

wer On

Button

d and

four more that are accessed by pressing the

Macro

Buttons

1. Press the

Mute Button and the Macro

Button

to be programmed or the

Power On Button d at the same time.

Input Selector will light red, and the Program/

SPL Indicator

c will flash amber.

2. Enter the steps for the macro sequence by press-

ing the button for the actual command step.

Although the macro may contain up to 19 steps,

each button press

, including those used to change

devices, counts as a step. The

Program/SPL

Indicator

c will flash green to confirm each

button press as you enter commands.

NOTE: While entering commands for Power On/Off of

any device during a macro sequence, press the

Mute

Button

DO NOT press the actual Power button.

3. When all the steps have been entered, press the

Sleep Button j to enter the commands. The

red light under the

Input Selectors ef will

blink and then turn off.

Example: To program the Macro 1 button so that it

turns on the AVR, TV and a cable box, follow these

steps:

• Press the

Macro 1 Button and Mute

Button

at the same time and then release

them.

• Note that the

Program/SPL Indicator c will

flash amber.

• Press the

AVR

Selector

• Press the

Mute Button to store the AVR’s

power on command.

• Press the

VID 3 Input Selector Button e to

indicate the next command is for “TV Power On.”

• Press the

Mute

Button

to store the

Power On Command.

• Press the

VID 2 Input Selector

Button

e to

indicate the next command is for “Cable Power On.”

• Press the Mute Button to store the Cable

ower On command.

• Press the

Sleep/Channel Up

Button

j to

complete the process and store the macro

sequence.

After following these steps, each time you press

the

Macro 1

Button

the remote will send

the Power On/Off command.

8 PROGRAMMING THE REMOTE

RCP 2 Remote OM 10/4/04 4:38 PM Page 10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon RCP2 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon RCP2 Manual

Product: