534547
4
Zoom out
Zoom in
Previous page
1/12
Next page
PL0004-01001
1
2
3
4
5
8
9
6
7
4
4 5
HKTS200SUB Rear-Panel Connections
Subwoofer Level Control:
.
Use this control to adjust the HKTS200SUB’s volume. Turn
clockwise to increase the volume; turn counterclockwise to decrease the volume.
Bass Boost Switch:
1.
Set this switch to ON to enhance the HKTS200SUB’s low-frequency
performance. Set this switch to OFF for normal low-frequency performance.
Phase Switch:
2.
The Phase Switch
2
determines whether the HKTS200SUB’s piston-like
action moves in and out in phase with the satellite speakers. If the subwoofer were
to play out of phase with the satellite speakers, the sound waves produced by the
subwoofer could be canceled out, reducing bass performance and sonic impact. This
phenomenon depends in part on the relative placement of all the speakers in the
room. In most cases the Phase Switch
2
should be left in the NORMAL position.
However, it does no harm to experiment, and you can leave the Phase Switch
2
in
the position that maximizes bass response and impact.
Power On Mode Switch:
3.
When set in the AUTO position and when the Power Switch
7
is set to ON, the HKTS200SUB will automatically turn itself on when it receives an
audio signal, and will enter the standby mode once no audio signal has been received
for about 15 minutes. When this switch is set in the ON position, the HKTS200SUB
will remain on whether or not it is receiving an audio signal.
An LED on the HKTS200SUB’s top panel indicates whether the subwoofer is in the on
or standby state:
When the LED is illuminated white, the HKTS200SUB is turned on.
When the LED is not illuminated, the HKTS200SUB is in standby mode.
When the Master Power Switch
7
is set to OFF, the LED will not be
illuminated, no matter what setting the Power On Mode Switch
3
is in.
External Trigger Input:
4.
Use the mini-plug of the supplied combination LFE and trigger
cable to connect the External Trigger Input to the trigger output of another
compatible component. Whenever a trigger signal between 3 and 30V (AC or DC) is
detected, the HKTS200SUB’s amplifier will turn on. The HKTS200SUB’s amplifier will
turn off after the trigger signal ceases. (This will occur even when the Power On
Mode Switch
3
is in the AUTO position.)
Line-Level LFE In Connector:
5.
Use the LFE (purple) connector of the supplied combination
LFE and trigger cable to connect the Line-Level LFE In to the dedicated subwoofer
output of a receiver or preamp/processor. This input bypasses the HKTS200SUB’s
internal crossover circuitry, so it should only be used with a subwoofer output that has
been low-pass filtered. If your receiver or preamp/processor does not have a dedicated
subwoofer output that is low-pass filtered you should use the HKTS200SUB’s Line-
Level L/R In Connectors
6
instead.
Line-Level L/R In Connectors:
6.
Use these connectors if your receiver or preamp/processor
does not have digital surround sound decoding or a subwoofer output that is low-pass
filtered.
If your receiver or preamp/processor has a separate subwoofer output, use the LFE
(purple) connector of the supplied combination LFE and trigger cable to connect it to
either one of the HKTS200SUB’s Line-Level L/R In Connectors.
If your receiver or preamp/processor does not have a separate subwoofer output,
use two Y-adapters (not supplied). Connect an adapters single end to the unit’s
preamp output for that channel. Connect one of the adapter’s dual ends to the main
amp input for that channel, and connect the adapter’s other dual end to one of the
HKTS200SUB’s Line-Level L/R In Connectors. Repeat with the other Y-adapter,
preamp channel, main amp input and HKTS200SUB Line-Level L/R In Connector.
Power Switch:
7.
Set this switch in the ON position to turn the HKTS200SUB on. The
subwoofer will then either be on or in standby mode, depending on the setting of the
Power On Mode Switch
3
.
Power Cord (Non-Detachable):
8.
After you have made and verified all subwoofer
and speaker connections described in this manual, plug this cord into an active,
unswitched electrical outlet for proper operation of the HKTS200SUB. DO NOT plug this
cord into the accessory outlets found in some audio components.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon HKTS 9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon HKTS 9 in the language / languages: English as an attachment in your email.

The manual is 2,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon HKTS 9

Harman Kardon HKTS 9 User Manual - German - 12 pages

Harman Kardon HKTS 9 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info