769909

Harman Kardon HKTS 2 MkII Manual

5
Zoom out
Zoom in
Previous page
1/16
Next page
REAR PANEL CONNECTIONS 5
Rear Panel Connections
Phase Switch: This switch determines
whether the subwoofer’s piston-like action
moves in and out in phase with the main speak-
ers. If the speakers were to play out of phase,
the sound waves produced by the subwoofer
would be cancelled out, reducing bass response.
This phenomenon depends in part on the rela-
tive placement of the speakers in the room. In
most cases, the Phase Switch
should be
left in the
NORMAL
position. However, it does
no harm to experiment with the Phase Switch
, and you may leave it in the position that
maximizes bass response.
Line-Level Subwoofer (SUB) Input: Con-
nect the subwoofer output of a receiver with
digital surround sound decoding, such as Dolby*
Digital or DTS®, to this input. This input bypasses
the subwoofer’s internal crossover circuitry, and
should only be used with a filtered signal. If your
receiver does not have digital decoding, you
should use the Line-Level Full-Range Inputs
instead.
Line-Level Full-Range Inputs: Connect
the line-level subwoofer output or preamp out-
put(s) of your receiver or amplifier to these
inputs. If your receiver does not have a separate
subwoofer output, use a Y-adapter (not supplied)
to bridge the receiver’s preamp output to the
main amp input for that channel, and connect
the long end of the adapter to the correspon-
ding line-level input on the subwoofer. If your
receiver has only a single subwoofer output, you
may connect it to either the left or right line-
level input on the subwoofer, and no Y-adapter is
needed.
Speaker-Level Outputs: If you are using
the Speaker-Level Inputs
on the
subwoofer, you should connect these binding-
post terminals to your front left and right speak-
ers, remembering to maintain polarity by con-
necting the (+) terminal on the subwoofer to the
(+) terminal on the speaker, and the (–) terminal
on the subwoofer to the (–) terminal on the
speaker. If you are not using the Speaker-Level
Inputs
, then connect your front left and
right speakers directly to your receiver or
amplifier. See pages 9 through 12 for further
information on speaker connections.
Speaker-Level Inputs: Connect these
binding-post terminals to the main left and right
speaker terminals of your receiver or amplifier, if
your receiver or amplifier does not have a line-
level subwoofer output. Remember to maintain
polarity by connecting the (+) terminal on the
receiver/amplifier to the (+) terminal on the sub-
woofer, and the (–) terminal on the receiver/
amplifier to the (–) terminal on the subwoofer.
Master Power Switch: Place this switch in
the “•” position to power-on the subwoofer. The
subwoofer will then be either in the Standby
mode or completely on, depending on the
position of the Trigger On/Off Switch
.
AC Power Cord: Make sure to plug this
cord into an active, unswitched electrical outlet
for proper operation of the subwoofer.
The cord should not be plugged into the
accessory outlets found on some audio
components.
0127CSK - HK TS2_ENG.qxp:29515_HKTS2_English 18/03/09 16:07 Side 5
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon HKTS 2 MkII at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon HKTS 2 MkII in the language / languages: English as an attachment in your email.

The manual is 0.43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info