Manual Harman Kardon DPR 1001 (page 31 of 44) (English)

456609

Zoom out

Zoom in

1/44

MULTIROOM OPERATION 31

MULTIROOM OPERATION

To change the length of time that the semi-OSD dis-

plays remain on the screen, go to the

ADVANCED

menu as outlined earlier, and press the

⁄

Navigation Buttons n as needed, until the

SEMI OSD TIME OUT line is highlighted

in reverse video. Next, press the

‹

›

Navigation

Buttons

n until the desired time in seconds is dis-

played. Unlike most of the other options in this menu,

this is a permanent setting change, and the time-out

entry will remain in effect until it is changed, even

when the unit is turned off.

If you wish to make other adjustments, press the

⁄

Navigation Buttons n until the desired set-

ting is highlighted in reverse video, or highlight the

RETURN TO MAIN MENU line and then

press the

Set Button p to select another menu for

adjustment. If no further adjustments are required,

press the

OSD Button to exit the menu system.

Full-OSD Time-Out Adjustment

The FULL OSD menu system is used to simplify

the setup and adjustment of the DPR 1001, using a

series of on-screen menus. The factory default setting

for these menus leaves them on the screen for 20

seconds after a period of inactivity before they disap-

pear from the screen (Time-Out). Time-Out is a safety

measure to prevent image retention of the menu text

in your monitor or projector, which might happen if it

were left on indefinitely. However, some viewers may

prefer a slightly longer or shorter period before the

Time Out display.

To change the Full-OSD Time-Out, you will need to

make an adjustment in the

ADVANCED menu

(Figure 13). To start the adjustment, press the

OSD

Button

to bring the MAIN menu to the

screen. Press the

¤ Navigation Button n, until

the

ADVANCED line is highlighted in reverse

video. Press the

Set Button p to enter the

ADVANCED menu (Figure 13).

At the

ADVANCED menu (Figure 13) make

certain that the

FULL OSD TIME OUT line

is highlighted in reverse video by pressing the

⁄

Navigation Buttons n as needed. Next, press the

‹

›

Navigation Buttons n until the desired time

is displayed in seconds. Unlike most of the other

options in this menu, this is a permanent setting

change, and the Time-Out entry will remain in effect

until it is changed, even if the unit is turned off.

If you wish to make other adjustments, press the

⁄

Navigation Buttons n until the desired set-

ting is highlighted in reverse video, or highlight the

RETURN TO MAIN MENU line and then

press the

Set Button p to select another menu for

adjustment. If no further adjustments are required,

press the

OSD Button to exit the menu system.

Multiroom Operation

The DPR 1001 is fully equipped to operate as the

control center for a multiroom system with optional

remote external infrared (IR) sensors, speakers and

power amplifiers. Although some multiroom installations

will require the services of a specially trained installer, it is

possible for the average do-it-yourself hobbyist to install

a simple remote room system.

Installation

The key to remote room operation is to link the remote

room to the DPR 1001’s location with wire for an

infrared link and speakers or an amplifier. For installation

instructions for Multiroom use, see page 15.

Multiroom Setup

Once the audio and IR link connections have been

made, the DPR 1001 needs to be configured for multi-

room operation using the steps below. Press the

OSD

Button

to bring the MAIN menu (Figure 1)

to the screen. Press the

Navigation Button n

until the MULTI-ROOM line is highlighted. Press

the

Set Button p to enter the MULTI-ROOM

menu (Figure 14).

Figure 14

When the MULTI-ROOM menu appears, the

MULTI-ROOM line will be highlighted. Since this

line is used to turn the system on and off, do not make

an adjustment here unless you wish to turn the system

on at this time. To turn the system on, press the

›

Navigation Button n so that ON appears. If you do

not wish to turn the system on at this time or to proceed

to the next step, press the

Navigation Button n

so that the MULTI IN line is highlighted.

At the

MULTI IN line, press the

‹

›

Navigation

Buttons

n until the desired input to the multiroom

system appears. When the selection has been made,

press the

Navigation Button n once so that the

MULTI VOL line is highlighted.

At the

MULTI VOL line, press the

‹

›

Navigation Buttons n until the desired volume level

for the multiroom system is entered. DO NOT use the

regular volume control knobs for this setting. When all

settings for the multiroom setup have been made,

press the

⁄

Navigation Buttons n until the

RETURN TO MAIN MENU line is highlighted.

If you have no other adjustments to make, press the

OSD Button to exit the menu system.

Multiroom Amplifier Configuration

Since the DPR 1001 is equipped with seven channels

of amplification, they may be allocated to either full 7.1

channel operation, or they may alternatively be used to

power speakers that are fed the output of the multiroom

system. Thus, when only 5.1 channels are required for

the main listening room, you may power speakers in a

second zone without the need for additional external

amplifiers. This is a major improvement over the use of

simple “Speaker A/B” switches, as it allows for a fully

separate source and independent volume levels at the

remote location.

To configure the DPR so that the amplifiers normally

used for the Surround Back channels are used for the

multiroom system, you must make an adjustment in the

ADVANCED menu (Figure 13). To start the adjust-

ment, press the

OSD Button to bring the

MAIN menu to the screen. Next, press the

Navigation Button n until the ADVANCED line

is highlighted in reverse video. Press the

Set Button

p to enter the ADVANCED menu.

When the

ADVANCED menu is on the screen, the

SB AMPS item at the top of the menu list will be

highlighted in reverse video. Press the

‹

›

Navigation

Buttons

n so that the right side of the menu line

changes to

MULTI ROOM.

When this configuration adjustment is complete, press

the

⁄

Navigation Buttons n until RETURN

TO MAIN MENU

is highlighted in reverse video

and press the

Set Button p to select another menu

for adjustment. If no further adjustments are required,

press the

OSD Button to exit the menu system.

IMPORTANT NOTE: Once the amplifiers are configured

as shown above so that the multiroom outputs are pow-

ered by the DPR’s internal amplifier, the speaker configu-

ration will automatically be reset for 5.1 channel opera-

tion in the main room. This means that 6.1/7.1-channel

operation will not be possible until the setting shown

above is returned to OFF. For that reason, use of the

internal amplifier for multiroom operation is recommended

only if your main listening room uses a 5.1 speaker

system. If the main room has a 6.1 or 7.1 speaker

setup, it will be necessary to use an optional, external

power amplifier to power the speakers used in the

multiroom system.

* MULTI-ROOM *

MULTI-ROOM:OFF

MULTI IN :FM PRESET01

MULTI VOL :25dB

RETURN TO MAIN MENU

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon DPR 1001 in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon DPR 1001 Manual

Product: