502638
25
Zoom out
Zoom in
Previous page
1/60
Next page
SYSTEM CONFIGURATIONSYSTEM CONFIGURATION
SYSTEM CONFIGURATION 25SYSTEM CONFIGURATION 25
When Dolby Pro Logic II Music or Dolby Pro Logic IIx
Music is selected as the listening mode, three special
settings are available to tailor the sound field to your
listening room environment and your individual taste
and preferences. (When other Dolby Surround modes
are selected, dotted lines will indicate that these set-
tings are not active.)
• Center Width: This setting adjusts the balance of the
vocal information in the front soundstage between
the center and front left/right speakers. The lower
settings spread the center channel sound more
broadly into the left and right channels. A higher
number (up to “7”) produces a tighter center chan-
nel presentatioin.
• Dimension: This setting alters the perceived depth
of the surround field by creating a shallower presen-
tation that appears to move sounds toward the front
of the room, or a deeper presentation that appears
to move the center of the sound field toward the
back of the room. The setting of “O” is a neutral
default, with the range of adjustment shown as
“R-3” for a deeper, rear-oriented sound to “F-3”
for a shallower, front-oriented sound.
• Panorama: Switch this setting on or off to add an
enveloping wrap-around presentation that increases
the perception of sound along the sides of the room.
To change these parameters, press the
¤
/
Navigation Buttons o while the DOLBY
SURROUND menu is on the screen until the
cursor is pointing to the line on the menu with the
parameter you wish to change. Then, press the
/
Navigation Buttons o to alter the setting to
your taste.
When the DOLBY DIGITAL mode is
selected,
there are additional settings available for
the Night mode, as shown in Figure 6.
Figure 6
The Night mode is a feature of Dolby Digital that pre-
serves the dynamic range and full intelligibility of a
movie soundtrack while reducing the peak level. This
prevents abruptly loud transitions from disturbing
others, without reducing the sonic impact of a digital
source. The Night mode is only available when specially
encoded Dolby Digital signals are played.
To adjust the Night mode setting, make certain that the
cursor is on the NIGHT line of the DOLBY
menu. Next, press
/
Navigation Button o to
choose between the following settings, as they appear
in the on-screen display:
OFF: When OFF is shown, the Night mode will
not function.
MID: When MID is shown, a mild compression
will be applied.
MAX: When MAX is shown, a more severe com-
pression algorithm will be applied.
We recommend that you select the MID setting as
a starting point and change to the MAX setting later,
if desired.
The Night mode may also be adjusted directly any
time a Dolby Digital source is playing by pressing
the Night Mode Button T. When the button is
pressed, D-RANGE will appear in the lower third
of the video screen and in the Lower Display Line
$. Press the Night Mode Button T within three
seconds to select the desired setting.
When all settings for the surround setup have been
made, press the
/
¤
Navigation Button o
so that the
cursor is next to BACK TO
MASTER MENU, and press the Set Button
q to return to the MASTER MENU.
In the DTS menu, the selection choices made with
the
/
Navigation Button o on the remote are
determined by a combination of the type of program
material in use and whether the 5.1- or 6.1/7.1-
channel configuration is in use.
When a DTS digitally encoded source is playing, the
choice of modes for 7.1 systems will vary according
to the program source (DTS 5.1, DTS-ES Matrix or
DTS-ES Discrete). Press the
/
Navigation Button
o to scroll through the choices available for your
system and the program in use. The DTS Neo:6 Music
mode is available with analog and PCM digital stereo
sources and the DTS Neo:6 Cinema mode may be
used with matrix surround-encoded sources for an
enhanced 5.1-channel sound field.
When the 5.1 configuration is in use, the AVR will
automatically select the 5.1 version of DTS processing
when a DTS data stream is detected. When the 6.1/
7.1 mode is selected, the DTS-ES Discrete mode will
automatically be activated for DTS sources with the ES
Discrete “flag. When a non-ES DTS disc is in use, you
may select the DTS-ES Matrix mode to create a full
7.1 surround mode. See page 36 for an explanation
of the DTS modes.
When an analog or two-channel PCM source is play-
ing, the DTS Neo:6 modes are available, which cre-
ates a three-, five- or six-channel presentation of
the sound. The exact modes available will depend on
the number of speaker positions established in the
SPEAKER SETUP menu. (See page 26 to
configure the system for the number and type of
speakers in your system.)
In the LOGIC 7
menu, the choices available
are
determined by whether the 5.1- or 6.1/7.1-channel
configuration is in use. In either case, the selection of a
Logic 7 mode enables Harman Kardon’s exclusive
Logic 7 processing to create multichannel surround
from two-channel stereo- or matrix-encoded program-
ming such as VHS cassettes or television broadcasts
produced with Dolby Surround.
With 5.1 configurations, you may select the Logic 7/5.1
Music, Cinema or Enhance modes. They work best
with surround-encoded programs or two-channel pro-
gramming of any type. For 6.1/7.1 configurations,
the Music and Cinema modes may be selected. The
Logic 7 modes are not available when either Dolby
Digital or DTS Digital soundtracks are in use. See
page 36 for an explanation of the Logic 7 modes.
In the DSP (SURR) menu, the choices made
with the
/
Navigation Button o select one of
the DSP surround modes designed for use with two-
channel stereo programs to create a variety of sound
field presentations. The Hall and Theater modes are
designed for multichannel installations, while the two
VMAx modes are optimized for use in delivering a full
surround field when only front left and front right
speakers are installed. See page 36 for an explanation
of the DSP surround modes.
In the STEREO menu, the choices made with the
/
Navigation Buttons o include a traditional
two-channel stereo presentation that uses only the left
and right front speakers. When SURROUND
OFF is selected, the unit is in a full bypass mode
with no bass management or other processing applied
to the signal as it is routed directly from the input to
the volume stage. When SURROUND OFF +
DSP is selected, you will still have a two-channel
presentation, but bass management is applied.
You may also select a 5 CH STEREO and 7
CH STEREO mode, depending on how many
speakers are available. These two modes feed a two-
channel presentation to the front left/right and sur-
round speakers, as stereo pairs, with a mix of the left
and right channels fed to the center speakers. See
page 36 for a complete explanation of the stereo
modes.
This menu also includes a setting to turn the unit’s
upsampling feature on or off. In normal use, this
feature is turned off, which means that digital sources
** DOLBY SURROUND **
MODE: DOLBY DIGITAL
CENTER WIDTH: ---
DIMENSION : ---
PANORAMA : ---
NIGHT : OFF
BACK TO SURR SELECT
AVR7300(120v)-OM 6/14/04 9:15 AM Page 25
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR7300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR7300 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info