502638
24
Zoom out
Zoom in
Previous page
1/60
Next page
SYSTEM CONFIGURATION
24 SYSTEM CONFIGURATION24 SYSTEM CONFIGURATION
In cases in which you wish to have the output of a
digital source selected as the record output feed, while
the cursor is next to the REC OUT line, press
the / Navigation Button o so that DSP
DOWNMIX appears. When this
indication is shown,
the AVR will feed a downmixed, analog version of a
Dolby Digital or DTS-encoded sig
nal to the Record
Output jacks (associated
with the Tape , Video 1
π and Video 2 sources and the Video 5
jacks when they are configured as an output). This
enables you to make an analog recording (where per-
mitted by copyright laws) of the soundtrack from a
digital source.
As a reminder, to ensure that a signal feed is always
available to the record output jacks, we recommend
that an analog connection be made as a fallback for
all digital sources. This is key with sources such as
cable set-tops to ensure that a record feed will continue
in the event that the digital audio stream is not avail-
able when channels are changed.
When all needed adjustments have been made, press
the
¤
Navigation Button o until the cursor is
next to BACK TO MASTER MENU to con-
tinue with the system configuration.
Audio Setup
The AUDIO SETUP menu contains a series of
submenus that are used to establish the settings that
optimize the audio output of the AVR 7300 to the
specifics of your home theater system and the envi-
ronment of the room it is placed in. While the factory
defaults may be used for some installations, we
strongly recommend that you take a short amount of
time to run through each of these menus to make
certain that any needed adjustments are made. The
end result will be a system that is properly configured
to provide all the power and performance that the
AVR 7300 was designed to deliver.
To reach the main AUDIO SETUP menu, press
the OSD Button U, and then press the Set Button
q. When the MAIN MENU (Figure 1) appears
on your video screen, press the
¤ Navigation
Button o once so that the on-screen cursor is
pointing to AUDIO SETUP and press the Set
Button q again. The main AUDIO SETUP
menu (Figure 3) will appear on the screen.
Figure 3
Surround Select and Setup
T
he next step is to set the surround mode you wish
to use with the input that was previously selected in
the IN/OUT SETUP menu. Since surround
modes are a matter of personal taste, feel free to
select any mode you wish – you may change it later.
However, to make it easier to establish the initial
parameters for the AVR 7300, it is best to select
Dolby Pro Logic II (Movie or Music) or Logic 7
(Cinema or Music) for most analog inputs and Dolby
Digital for inputs connected to digital sources. In the
case of inputs such as a CD player, tape deck or
tuner, you may wish to set the mode to Stereo
(“Surround Off”) as they are not typically used with
multichannel program material, and it is unlikely that
sur
round-encoded material will be used. Alternatively,
the
Logic 7 Music mode is a good choice for
stereo-only source material. See page 36 for more
information on available surround modes.
For digital program material, the AVR will always exam-
ine the data stream and automatically select a Dolby
Digital or DTS mode as applicable.
It is easiest to complete the surround setup using the
full-OSD on-screen menus. From the AUDIO
SETUP menu (Figure 3), press the
/
¤
Navigation Button o until the cursor is next to
the SURROUND SELECT line. Press the Set
Button q until the SURROUND SELECT
menu (Figure 4) is on the screen.
Figure 4
Each of the option lines on this menu (Figure 4)
selects the surround mode category, and within each
of those categories there will be a choice of the
specific mode options.
The choice of modes will vary according to the speaker
configuration in your system. When the SURR
BACK line of the SPEAKER SETUP menu
(Figure 7) is set to NONE the AVR 7300 will be
configured for 5.1-channel operation, and only the
modes appropriate to a five-speaker system will
appear. When the SURR BACK line of the
SPEAKER SETUP menu (Figure 7) is set to
SMALL or LARGE, the AVR 7300 will be con-
figured for 6.1/7.1-channel operation, and additional
modes such as Dolby Digital EX, Dolby Pro Logic IIx
and DTS-ES will appear, as they are only available
when seven main speakers are present. In addition,
some of the modes available in the AVR 7300 will not
appear unless a digital source is selected and is play-
ing the correct bitstream.
To select the mode that will be used as the initial default
for an input, first press the
/
¤
Navigation Button
o until the on-screen cursor is next to the desired
mode’s master category name, such as DOLBY
SURROUND, DTS, DSP (SURR) or
VMAx. Next, press the Set Button q to view the
submenu. Press the
/
Navigation Button o to
scroll through the available choices, and then press the
¤
Navigation Button o so that the cursor is next
to BACK TO MASTER MENU to continue
the setup process.
The following paragraphs detail the instructions needed
for modes with multiple choices.
On the DOLBY SURROUND menu (Figure 5),
choices include Dolby Digital, Dolby Pro Logic II, Dolby
Pro Logic IIx, Movie and Music, Dolby Pro Logic and
Dolby Virtual Speaker Reference or Wide. For a
complete descripton of the different Dolby Surround
modes, see page 36. The Dolby Digital EX and Dolby
Pro Logic IIx modes are only available when the
system is set for 6.1/7.1 operation by configuring
the Surround Back speakers to “Small” or “Large” as
described on page 26. When a disc is playing with a
Dolby Digital soundtrack that contains a special “flag”
signal in the data stream, the Dolby Digital EX mode
will be selected automatically. It may also be selected
using this menu or through the front-panel or remote
controls, as shown on page 35. A complete explana-
tion of these modes is found on page 36.
Figure 5
When the cursor is pointing to the MODE line,
press the
/
Navigation Buttons o to select the
desired Dolby surround mode, again remembering that
the choice of available modes will vary with the type of
program material being played and the number of
speakers in your system configuratioin.
** DOLBY SURROUND **
MODE: DOLBY PLII
MUSIC
CENTER WIDTH: 3
DIMENSION: 0
PANORAMA: OFF
NIGHT: -----
BACK TO SURR SELECT
** SURROUND SELECT **
DOLBY SURROUND
DTS
LOGIC 7
DSP (SURR)
VMAx
UPSAMPLING: ---
BACK TO AUDIO SETUP
** AUDIO SETUP **
SURROUND SELECT
SPEAKER SETUP
DELAY ADJUST
CHANNEL ADJUST
TONE CONTROLS
BACK TO MASTER MENU
1
4
AVR7300(120v)-OM 6/14/04 9:15 AM Page 24
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR7300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR7300 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info