502558

Harman Kardon AVR645 Manual

56
Zoom out
Zoom in
Previous page
1/68
Next page
56 PROGRAMMING THE REMOTE
Programming the Remote
Changing Devices
In the factory default settings, the AVR remote is
programmed so that the commands transmitted
correspond to the device selected by pressing
one of the Input Selectors
4
. This is logical,
as you want the remote to control the device you
have selected. However, in some circumstances
you may have configured your system so that the
devices connected to the AVR do not correspond
to the default device settings and the legends
printed on the remote. For example, if your
system has two VCRs you may connect the
second VCR to the VID 2 input.There is no
problem in doing that, but in normal operation
the commands issued after selecting the VID 2
input are for a television, not a VCR.
The AVR remote allows you to correct that
situation through the “Changing Devices”
process. That enables you to assign the codes
from one type of device to a different button. For
example, in the steps below, we will explain how
to program the VID 2 buttons to provide the
commands to operate a VCR. Of course, you may
program the remote to have any of the devices
take on the code set of any other device, as your
system requires. And, with the AVR remote’s
“Rename” function, you can even change the
way the name of the device appears on the
remote’s LCD display so that you see exactly
which commands are being sent.
To program the buttons normally assigned to one
device for the commands of another, follow these
steps:
1. Press and hold the Program Button
a
for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display
2
. Release the
button when the red light under the Set
Button
F
appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button
F
will remain illuminated in
red. Press the
⁄
Navigation Buttons
E
twice so that CHANGE DEVICE appears on
the bottom line of the LCD screen, as shown in
Figure 44. Press the Set Button
F
to begin
the process of reassigning the commands used
for a particular device.
Figure 44
3. The next menu display is where you select the
Input Select, or device, that you wish to
change. When the display shown in Figure 45
appears, press the
⁄¤
Navigation
Buttons
E
to scroll through the list to find
the device you wish to use for another
function. In this case we will select “TV,” and
show how to change it to take on the codes
for operating a VCR.When that device’s name
appears, press the Set Button
F
.
Figure 45
4. Once the “old” device type has been selected,
you need to tell the remote which set of
remote codes to use as a replacement for the
device just selected. When the instructions
shown in Figure 46 appear, press the
⁄¤
Navigation Buttons
E
to scroll through
the list of device categories to find the name
of the device that you wish to use. The old
device name will remain on the left side of the
LCD screen, while the replacement device list
will scroll to its right. For example, press the
⁄
Navigation Buttons
E
until the display
screen reads TV
<-VCR to have the VID 2/TV
Button transmit the commands used to control
a VCR. Press the Set Button
F
when the
desired device combination appears.
Figure 46
5. Once the new device is selected, the
remainder of the process will select the codes
for the specific brand to be used, and for that
reason they are identical to the way a device is
programmed using manual entry. Continue the
process as outlined in the next few steps,
remembering that if the codes for your specific
device are not found you may select any brand
and then “learn” the proper codes into the
AVR remote using the process outlined on
page 54. To begin the process, start by
selecting the brand of device, as shown in
Figure 29. Press the
⁄¤
Navigation
Buttons
E
until the brand name of the
device you are programming into the remote
appears on the lower line of the display and
then press the Set Button
F
.
6. The next step is important, as it determines
which codes will operate the source device or
display. Point the AVR remote at the device
being programmed and, following the
instructions shown on the remote’s LCD
Information Display
2
, press and release
the Numeric Keys
H
one at a time,
starting with the “1” button. After you press
the “1” Button
H
the remote’s LCD screen
will briefly go blank as the code is being
transmitted, but you will see the “transmit”
icon in the upper right corner of the display to
serve as confirmation that the remote is
sending out commands.
7. After you press and release the number key,
watch the device being programmed to see
whether it turns off.As shown in the
instructions that will appear on the next menu
screen (Figure 31), press the Set Button
F
,
and then skip to Step 9. If the unit does not
turn off, proceed to the next step.
8. If the device being programmed into the AVR
remote does NOT turn off after you have
pressed the “1” key, continue Steps 6 and 7 by
pressing the available numeric keys shown
until the device turns off. If the device still does
not turn off after all choices have been tried,
the code for this specific device is not in the
AVR remote library under that brand name. If
that is the case, we suggest that you press the
Set Button
F
to accept the codes from
another brand so that the programming is
completed, but remember that you will then
have to program the remote manually by
following the Learning Commands instructions
on page 54.
9. When the device being programmed does
turn off after a numeric key has been
pressed, you must press the Set Button
F
within five seconds to enter the setting into
the remote’s memory. After you press the Set
button, the top line of the LCD display will
read SAVING... and then the word SAVED
will flash four times in the center of the
bottom line.
10.When the codes are saved the remote will
return to normal operation, and whenever you
press the Input Selector Button
4
that
was just programmed, the display will show the
original device type code at the far left side of
the display, with the name of the new code set
type in brackets. For example, the display will
read TV
<-VCR in our example of replacing
the TV codes with those for a VCR.
Macro Programming
Macros enable you to easily repeat frequently used
combinations of multiple remote control
commands with the touch of a single button. Once
a macro is programmed you may send up to 20
commands with one press of the Power On or
Macro buttons. This will greatly simplify the process
of turning on your system, changing devices or
other common tasks. Thanks to the remote’s two-
line display, it is easier than ever for you to take
advantage of the power of macro commands.
Recording a Macro
To record a macro into the remote’s memory,
follow these steps:
1. Press and hold the Program Button
a
for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display
2
. Release the
button when the red light under the Set
Button
F
appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button
F
will remain illuminated in
red. Press the
⁄
Navigation Buttons
E
three times so that MACRO appears on the
bottom line of the LCD screen, as shown in
Figure 47. Press the Set Button
F
to enter
the main macro menu branch.
NEW DEVICE TYPE
TV< -VCR
OLD DEVICE TYPE
TV
MAIN MENU
CHANGE DEVICE
29851_AVR645_ENG 30/10/06 9:46 Side 56
… 56 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR645 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR645 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR645

Harman Kardon AVR645 User Manual - German - 68 pages

Harman Kardon AVR645 User Manual - Dutch - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info