502558

Harman Kardon AVR645 Manual

54
Zoom out
Zoom in
Previous page
1/68
Next page
54 PROGRAMMING THE REMOTE
Programming the Remote
Although the AVR remote is preprogrammed with
an extensive library of codes for many major
brands, it is also possible that you may have
attempted to program a product that is too new
or too old, and thus not all of its commands will
be in the code library. You may fill in the codes
for any button that does not operate properly by
using the learning technique shown on page 54.
Automatic Code Entry
In addition to manual code selection using the
brand name list, it is also possible to
automatically search through all the codes that
are stored in the AVR remote’s library to see
whether a device will respond even if it is not
listed among the brands that appear when you
program the remote manually. To automatically
search through the codes that are available for a
specific device type (e.g., DVD, VCR), follow these
steps:
1. Turn on the power to the device you wish to
program into the AVR remote.This is
important, as in a later step you will need to
see whether the device turns off to determine
whether the remote has been programmed for
the proper remote codes.
2. Press and hold the Program Button
a
for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display
2
. Release the
button when the red light under the Set
Button
F
appears.
3. The remote’s MAIN MENU message (Figure
26) will appear in the LCD display and the Set
Button
F
will remain illuminated in red.
Press the Set Button
F
to begin the
process of selecting a device and locating the
proper remote codes.
4. SELECT A DEVICE will appear in the
LCD display (Figure 27).
Press the
⁄¤
Navigation Buttons
E
to
scroll through the list of device categories and
press the Set Button
F
when the device
for which you wish to set the codes appears.
For this example, we will select “TV” to enter
the codes needed to operate your TV.
5. At the next menu screen on the remote (Figure
28), press the
⁄
Navigation Buttons
E
so that the bottom line of the LCD display
reads AUTO (Figure 32) and then press the
Set Button
F
to enter the Automatic
programming mode.
Figure 32
6. As instructed on the next menu screen, press
the
⁄
Navigation Buttons
E
to begin
the automatic code search process. Your
confirmation that the remote is sending out
commands is the movement of a square block
across the top line of the LCD display screen
while the bottom line reads PLEASE WAIT….
You will also see the transmit icon in the upper
right corner of the LCD display’s top line to
remind you that the remote is working even
though you may not see anything happening
to the device being programmed.
7. It will take a few seconds for the remote to
send out the first group of commands, after
which you will see a new display in the LCD
screen, as shown in Figure 33. Following the
instructions, if the device being programmed
has NOT turned off, press the
⁄
Navigation
Buttons
E
again to send another group of
codes. If the device being programmed has
turned off, skip to Step 9.
Figure 33
8. By pressing the
⁄
Navigation Buttons
E
again, the remote will send out a new set of
commands. When it pauses, follow the
instructions shown in Step 7. Depending on
how many codes are stored for a specific
device type, you may have to repeat this
process as many as fifteen times. Remember, if
the device turns off, skip to Step 9.When all
the codes for the device being programmed
have been tried, the instruction shown in
Figure 34 will appear. This means that the
codes for the product you are trying to
program are not in the AVR remote library and
you will have to “learn” them into the remote
following the instructions shown on page 54.
Press the Set Button
F
as instructed to
exit the programming process.
Figure 34
9. If the device being programmed does turn off
after following the instructions in Step 7, you
will need to verify the code set by pressing the
Numeric Keys
H
in sequence, as instructed
in Figure 33. Point the remote at the device
being programmed, and press the “1” Button
H
to see whether the device turns back on.
10. After pressing and releasing the “1” Button
H
, check to see whether the device has
turned back on. If it has, skip to Step 12. If it
does not turn on, press the “2” Button
H
,
or the next button in the numeric sequence if
you are repeating the procedure, as
instructed by the LCD screen in Figure 35.
Figure 35
11. When pressing the “1” button does not turn
the device being programmed back on, repeat
the procedure by trying the remainder of the
Numeric Keys
H
in sequence, each time
pressing and then releasing the button to see
whether the new device turns back on. When
it does, skip to the next step. However, if you
try all 10 numeric keys and find that the unit
will not turn on, you won’t be able to use this
method to program the device. Press the
Clear Button
X
to exit the programming
process. You’ll need to follow the Learning
Commands instructions below to enter the
codes for this device into the AVR remote.
12. When pressing one of the numeric keys in
Step 10 or 11 causes the device being
programmed to turn back on, follow the
instructions shown in Figure 32 and press the
Set Button
F
within five seconds of the
device turning on. After you press the Set
button, the top line of the LCD display will
read SAVING… and then the word SAVED
will flash four times in the center of the
bottom line.
13. When the codes are saved, the remote will
return to normal operation, and whenever
you press the Input Selector Button
4
that was just programmed, the codes for the
new device will be used. If no further buttons
are pressed, the remote will revert back to
the default setting for AVR commands.
Learning Commands
On occasions when the AVR remote does not
contain the codes for a particular product’s
remote in its built-in library, or when you wish to
program a missing or special function into one
button of a device, the AVR remote’s learning
capability allows you to do that. To teach
commands from one product’s remote into the
AVR remote, follow these steps:
The process requires that both the device’s original
remote and the AVR remote be available. Before
pressing any buttons on either remote, place them
so that the IR transmitter on the remote from the
device to be programmed is facing the Infrared
Lens
1
on the AVR’s remote.The two remotes
should be no more than an inch apart, and there
should not be any direct sunlight or other bright
light source near the remotes.
1. Press and hold the Program Button
a
for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display
2
. Release the
button when the red light under the Set
Button
F
appears.
POWER ON?
Y - > SET N-> 1 ~ 0
REACH END POINT
EXIT -> SET KEY
POWER OFF?
Y - > 1~ 0 N->
PROGRAM DEVICE
AUTO
29851_AVR645_ENG 30/10/06 9:46 Side 54
… 54 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR645 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR645 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR645

Harman Kardon AVR645 User Manual - German - 68 pages

Harman Kardon AVR645 User Manual - Dutch - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info