502558
26
Zoom out
Zoom in
Previous page
1/68
Next page
26 SYSTEM CONFIGURATION
System Configuration
When the adjustment has been made, or if no
adjustment is required and all settings on this
page are complete, press the
/
¤
Navigation
Button
E
F until the on-screen cursor is
pointing to
PAGE 1 and then press the
Set Button
F
Q to return to the main
IN/OUT SETUP menu to configure another
input, or if no further input configuration adjust-
ments are needed, press the
/
¤
Navigation
Button
E
F until the on-screen cursor is
pointing to
MASTER MENU and then press
the Set Button
F
Q to return to the main
menu screen.
Video Monitor Settings
The VIDEO MONITOR SETTINGS
menu (Figure 10) is unique in that it contains a
mix of information display lines that detail status
information about the AVR 645’s video system
settings, along with a few lines where a specific
parameter may be changed. With the
MASTER
MENU
on the screen, press the
/
¤
Navigation Button
E
F until the on-
screen cursor is pointing to
VIDEO
MONITOR SETTINGS
and then press the
Set Button
F
Q to move to the menu
screen.
Figure 10
The IN VIDEOFORMAT line is an informa-
tional display of the resolution of the incoming
video stream, and may not be adjusted.
The
IN VIDEO COPYPROT line is an
informational display that shows whether or not
an incoming video signal contains copy
protection encoding, and may not be adjusted.
The
VIDEO PROCESS line is an informa-
tional display of the setting made in the
IN/OUT SETUP menu indicating how
incoming video is processed for the input being
viewed, and may not be adjusted.
The
COMPONENT OUT line is an informa-
tional display of whether or not the Component
Video outputs are
ENABLED or OFF, based
on the input signal type and resolution, and
whether or not the incoming video signal has
HDCP content protection. It may not be adjusted.
The
S-VIDEO OUT line is an informational
display of whether or not the S-video outputs are
available at a 576i resolution (or OFF), based on
the input signal type and resolution and whether
or not the incoming video signal has HDCP
content protection. It may not be adjusted.
The
DISPLAY INTER line allows you to
choose between an
ANALOG video output
default value and an HDMI/DVI output by press-
ing the
/
Navigation Button
E
F to
make the desired selection. When the setting is
ANALOG, the HDMI output is placed in a
Standby mode so that it automatically switches
to HDMI when an HDMI signal is detected. If a
high-definition input source is not HDCP-content-
protected, it may be output through the compo-
nent jacks; otherwise, it will be sent only to the
HDMI outputs. The
HDMI/DVI setting routes
all converted or processed video to the HDMI
outputs.
The HDMI AUDIO OUT line allows you to
choose whether a two-channel downmix of the
audio that accompanies the selected source is
sent over the HDMI connection (
YES) at the
maximum bit rate the display’s audio system is
capable of handling, or not (
NO). To change the
setting, press the
/
Navigation Button
E
F to make the desired selection.
When required adjustments have been made for
this input, or if no adjustment is required, press
the
/
¤
Navigation Button
E
F until
the on-screen cursor is pointing to
BACK TO
MASTER MENU
and then press Set Button
F
Q to return to the main menu screen.
Audio Setup
This menu allows you to configure the tone con-
trols. If you do not wish to change any of those
settings at this time, proceed to the next menu
screen. However, to make configuration changes
to those parameters, make certain that the
MASTER MENU is on the screen with the
cursor pointing to the
AUDIO SETUP line,
and press the Set Button
F
Q.The
AUDIO SETUP menu (Figure 12) will appear.
Figure 12
The first line controls whether or not the
bass/treble tone controls are in the signal path.
The normal default is for them to be in-line, but if
you wish to remove them from the circuit for
“flat” response, first make certain that the
cursor is pointing to the
TONE line on the
menu and press the
/
Navigation Button
E
F so that OUT is highlighted in reverse
video.
If you wish to leave the tone controls in the sig-
nal path, the amount off boost or cut for bass
and treble may be adjusted by pressing the
/
¤
Navigation Button
E
F so that the
cursor is next to the line for the setting you
wish to adjust. Next, press the
/
Navigation
Button
E
F until the desired setting is
shown.
When all desired changes have been made on
this menu, press the
/
¤
Navigation Button
E
F so that the cursor is next to the
BACK TO MAIN MENUline and press
the Set Button
F
Q.
* AUDIO SETUP *
TONE :IN OUT
BASS :0
TREBLE :0
BACK TO MASTER MENU
*VIDEO MONITOR SETTINGS*
IN VIDEO FORMAT: 1080i
IN VIDEO COPY PROT: ON
VIDEO PROCESS: V CONVERS
COMPONENT OUT: OFF
S-VIDEO OUT: OFF
COMPOSITE OUT: OFF
DISPLAY INTER: HDMI/DVI
HDMI AUDIO OUT: NO
BACK TO MASTER MENU
29851_AVR645_ENG 30/10/06 9:46 Side 26
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR645 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR645 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR645

Harman Kardon AVR645 User Manual - German - 68 pages

Harman Kardon AVR645 User Manual - Dutch - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info