502646
20
Zoom out
Zoom in
Previous page
1/47
Next page
System Configuration
17
System Setup
Once the speakers have been placed in the
room and connected, the final step in the
setup process is to enter the settings that
configure the AVR45’s bass management
system for the type of speakers used in
your system, the calibration of the output
levels and the delay times used by the sur-
round sound processor. Before proceeding
further, this is a good time to review the
installation section of the manual to
make certain that all connections are
properly made.
You are now ready to power up the AVR45
to begin these final adjustments.
1. Plug the Power Cable to an
unswitched AC outlet.
2. Press the Main Power Switch 1
in so that it latches in with the “OFF”
wording on the top of the switch
inside the front panel. Note that the
Power Indicator 3 will turn
amber, indicating that the unit is in
the Standby mode.
3. Install the four supplied AAA batteries
in the remote as shown. Be certain to
observe the (+) and (
) polarity
indicators shown in the bottom of the
battery compartment.
4. Turn the AVR45 on either by pressing
the System Power Control 3 on
the front panel, or via the remote by
first pressing the AVR Selector a,
and then pressing the Power button
c. The Power Indicator 3 will
turn green to confirm that the unit is
on, and the Information Display ˝
will also light up.
Speaker Configuration
The first few adjustments tell the AVR45,
which type of speakers are in use. This is
important as it adjusts the settings that
determine which speakers receive low-
frequency (bass) information. For each
of these settings use the LARGE setting if
the speakers for a particular position are
traditional full-range loudspeakers that
are capable of reproducing sounds
below 100Hz. Use the SMALL setting for
smaller, frequency-limited satellite
speakers that do not reproduce sounds
below 100Hz. Note that when “small”
speakers are used, a subwoofer is
required to reproduce low-frequency
sounds. Remember that the “large” and
“small” descriptions do not refer to the
actual physical size of the speakers, but
their ability to reproduce low-frequency
sounds. If you are in doubt as to which
category describes your speakers, consult
the specifications in the speakers’ owner’s
manual, or ask your dealer.
With the AVR45 turned on, follow these
steps to configure the speakers:
1. Put the AVR45 in the Dolby Pro Logic
mode by pressing the Dolby Pro
Logic Selector Ó on the front
panel or by pressing the Surround
Mode Selector yon the remote,
followed by the
/
¤
buttons g
until PRO LOGIC appears in the
Main Information Display S and
the PRO LOGIC indicator F lights.
2. Press the Speaker button on
the remote or front panel. The words
FRNT SPEAKER will appear in the
Main Information Display S.
3. Press the Set button .
4. Press the
/
¤
buttons g on the
remote or the Selector buttons¸
on the front panel until either
LARGE or SMALL appears to match
the type of speakers you have at the
left front and right front positions, as
described by the definitions shown
below.
When SMALL is selected, low-
frequency sounds will be sent to the
subwoofer output only. Note that if
you choose this option, and there is
no subwoofer connected, you will
not hear any low-frequency sounds
from the front channels.
AVR45 om (G).Eng,Fr 4/16/99 11:41 AM Page 17
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR45 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR45 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info