502548
45
Zoom out
Zoom in
Previous page
1/58
Next page
Programming the Remote
Notes on Using the AVR
Remote With Other Devices.
Manufacturers may use different code sets for
t
he same product category. For that reason, it is
important that you check to see if the code set
you have entered operates as many controls as
p
ossible. If it appears that only a few functions
operate, check to see if another code set will
work with more buttons.
Depending on the brand and product type
used the functions listed in the Function List
tables may not correspond with the function the
unit reacts on the command. In these cases it’s a
good idea to edit the reaction of the unit into
the corresponding line of the table or to set up a
separate list.
When a button is pressed on the AVR remote,
the red light under the Input Selector
cy
for the product being operated should flash
briefly. If the Device Control Selector flashes for
some but not all buttons for a particular
product, it does NOT indicate a problem with the
remote, but rather that no function is
programmed for the button being pushed.
P
unch-Through Programming
T
he AVR 355/AVR 255 remote’s punch-through
feature allows you to select one component for
the remote to operate, while simultaneously set-
ting certain groups of controls to operate anoth-
er component. For example, while using the AVR
to control surround modes and other audio func-
tions, you may operate the transport controls of
your DVD player. Or while using the remote to
control video functions on your TV, you may use
y
our cable box to change channels.
To program punch-through control while operat-
ing any device:
1. Press and hold the Source Selector (or AVR
selector) for the main device the remote will
be operating. The Source Selector will light, go
dark and then light up again, indicating the
remote is in Program mode and that you may
release the button.
2. Select the type of punch-through program-
ming.
a) To program channel control punch-through,
press the Channel Up Button.
b) To program transport control punch-
through, press the Play Button.
3. Press the Source Selector for the device whose
channel or transport controls you would like
to be active while operating the device you
selected in the first step.The Source Selector
will flash to confirm the programming.
For example, if you wish to watch your TV while
changing channels using your cable box, first
press the TV Button until it lights. Then press the
Channel Up Button, followed by the CBL/SAT
Button.
To undo punch-through programming, follow
the same steps as above, but press the same
Source Selector in Steps 1 and 3.
NOTE: The remote always allows volume-control
punchthrough, since the Volume and Mute con-
trols are dedicated to the AVR.
R
esetting the Remote Memory
As you add components to your home-theater
system, occasionally you may wish to totally
reprogram the remote control without the
confusion of any commands, activities or ”Punch-
Through“ programming that you may have done.
To do this, it is possible to reset the remote to the
original factory defaults and command codes by
following these steps. Note, however, that once
the remote is reset, all commands or codes that
you have entered will be erased and will need to
be re-entered:
1. Press the TV Device Button
c
and the "0"
n
umber Button
k
s
imultaneously.The TV button
lights up.
2. Press the ”3 button
k
three times.
3.After a number of seconds, depending on the
number of commands that are programmed and
need erasing, all the Device Buttons
c
as well as
the AVR Button
y
blink 3 times to indicate that
the remote has been reset to the factory settings.
ENGLISH
PROGRAMMING THE REMOTE 45
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR355 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR355 in the language / languages: English as an attachment in your email.

The manual is 3,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR355

Harman Kardon AVR355 User Manual - German - 58 pages

Harman Kardon AVR355 User Manual - Dutch - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info