502622
30
Zoom out
Zoom in
Previous page
1/76
Next page
Figure 32 – HDMI Monitor Output
Component Video: If the display does not have HDMI inputs, but
does have component video inputs, connect the Component Video
Monitor Outputs to the display (see Figure 33). As with HDMI connec-
tions, the AVR 354 is capable of converting composite and S-video
sources to the component video format, while upscaling the resolution to
as high as 1080i, depending on the display’s capabilities. Unlike HDMI
connections, component video connections do not enable the AVR 354
to detect the display’s capabilities and the appropriate resolution must
be selected manually, as described in the Initial Setup section.
Figure 33 – Component Video Monitor Outputs
Composite/S-Video: If the video display does not have HDMI or
component video inputs, connect the corresponding composite or
S-video Monitor Output to the display. If available, S-video is preferred
over composite video, and if used, the AVR 354 will convert composite
video sources to S-video. See Figure 34.
Figure 34 – Composite and S-Video Monitor Outputs
Consult the manual for your TV to make sure you understand how
to select the correct video input.
Step Six – Plug in AC Power
Having made all of your wiring connections, it is now time to plug each
component’s AC power cord into a working outlet.
You may plug one device into the AC Switched Accessory Outlet on the
rear of the AVR 354. See Figure 35. Make sure this device draws no
more than 50 watts. The device should have its mechanical or master
power switch turned on, and it will power on any time the AVR 354 is
turned on. If the device has a clock or must always be on, do not plug
it into this outlet.
Figure 35 – Switched AC Accessory Outlet
Before plugging the AVR 354’s AC Power Cord into an electrical outlet,
make sure that the Master Power Switch on the front panel is popped
out so that the word OFF appears on its top. Gently press the button to
turn the switch off. This will prevent the possibility of damaging the AVR
in case of a transient power surge.
The AVR 354 is equipped with a detachable power cord. It allows
you to fully wire your system before installing the AVR, which may be
required for some in-wall entertainment centers or custom applications.
The male end of the cord should be plugged into an unswitched AC
power outlet, and the female end should be plugged into the receptacle
on the AVR 354’s rear panel. See Figure 36.
Figure 36 – AC Power Input
Step Seven – Insert Batteries in Remote
The AVR 354 remote control uses four AAA batteries, which are included.
To remove the battery cover located on the back of the remote,
squeeze the tab and lift the cover.
Insert the batteries, as shown in Figure 37, making sure to observe
the correct polarity.
AVR 354
AVR 354
AVR 354
AVR 354
AVR 354
30
30
INSTALLATION
AVR354 OM.qxd 9/26/08 12:27 PM Page 30
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR354 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR354 in the language / languages: English as an attachment in your email.

The manual is 4,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info