502643

Harman Kardon AVR300 Manual

29
Zoom out
Zoom in
Previous page
1/40
Next page
29 PROGRAMMING THE REMOTE
Programming the Remote
the remote for Volume Punch-Through, follow
these steps:
1. Press the Input or Video Device Selector
c for the unit you wish to have associ-
ated with the volume control and the Mute
button at the same time until the red light
illuminates under the Device Selector.
2. Press the Volume Up button .
3. Press either the AVR b or the TV Device
Control Selector , depending on which
system’s volume control you wish to have
attached for the punch-through mode. Note
that the red light under the Device Control
Selector will blink twice and then go out
to confirm the data entry.
Example: To have the AVR’s volume control
activated even though the remote is set to
control the TV, first press the TV Device
Control Selector and the Mute button
at the same time. Next, press the
Volume Up button , followed by the
AVR Device
Control Selector b.
NOTE: Should you wish to return the remote to
the original configuration after entering a Volume
Punch-Through, you will need to repeat the steps
shown above. However, press the same Device
Control Selector in steps one and three.
Reassigning Device-Control
Selectors
Although any of the Input or Video Device
Selectors c is normally assigned to the
category of product shown on the remote, it is
possible to reassign one of these buttons to oper-
ate a second device of another type. For example,
if you have two VCRs but no cable box receiver,
you may program the CBL button to operate
a second VCR. Before following the normal pro-
gramming steps for either Three-Digit entry or Auto
Search code entry, you must first reassign the
button with the following steps:
1. Press the Input or Video Device Selector
c you wish to reassign and the Mute
button at the same time until the red
light illuminates under the Device Control
Selector .
2. Press the Input or Video Device Selector
c for the function you wish to
program into the reassigned button.
3. Enter the three-digit code for the specific
model you wish the reassigned button to
operate.
4. Press the same Input or Video Device
Selector c pressed in Step 1 once
again to store the selection.
Example: To use the CBL button to operate a
second VCR, first press the CBL Device
Control Selector and the Mute button
at the same time until the red light glows
under the CBL button. Press the VCR button,
followed by the three-digit code for the specific
model you wish to control. Finally, press the
CBL button again.
31
35
35
35
35
31
35
35
35
32
31
35
35
35
32
31
35
21
25
29
30
26
22
1
5
6
7
8
9
10
11
2
3
4
12
33
31
27
23
34
32
28
24
35
36
37 38
39
40
41
42 43 44
45
46
50
51 52
53
54 55
56
47
48
49
14
18
20
13
19
15
16
17
AVR 300
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR300 in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info