Manual Harman Kardon AVR 4000 (page 38 of 58) (English)

8518

Zoom out

Zoom in

1/58

38 ADVANCED FEATURES

Multiroom Operation

The AVR 4000 is fully equipped to operate as the

control center for a multiroom system with

optional remote external Infrared (IR) sensors,

speakers and power amplifiers.Although some

multi-room installations will require the services

of a specially trained installer, it is possible for

the average do-it-yourself hobbyist to install a

simple remote room system.

Installation

The key to remote room operation is to link the

remote room to the AVR 4000’s location with

wire for an infrared receiver and speakers or an

amplifier. For complete installation instructions

for Multiroom use, see page 18.

Multiroom Setup

Once the audio and IR link connections have been

made, the AVR 4000 needs to be configured for

multiroom operation using the steps below. Press

the OSD button

to bring the MASTER

MENU (Figure 1) to the screen. Press the

⁄

button

, until the on-screen

›

cursor is next

to the MULTI-ROOM line. Press the Set

button

to enter the MULTI-ROOM

SETUP menu (Figure 10).

Figure 10

When the MULTI-ROOM SETUP

menu appears, the on-screen

› cursor will be at

the MULTI-ROOM line. Since this line is

used to turn the system on and off, do not make

an adjustment here unless you wish to turn the

system on at this time. To turn the system on,

press the

› button

so that ONis high-

lighted. If you do not wish to turn the system on

at this time or to proceed to the next step, press

the

Button

once so that the › on-screen

cursor is next to the MULTI IN line.

At the MULTI IN line, press the

‹

›

but-

tons

until the desired Audio/Video input

to the multi-room system appears in the high-

lighted video. When the selection has been

made, press the

button

once so that the

›

on-screen cursor is next to the MULTI

VOLline.

At the MULTI VOL line, press the

‹

›

buttons

or hold them pressed until the

desired volume level for the multi-room system

is entered. DO NOT use the regular volume con-

trol knobs for this setting. When all settings for

the multiroom setup have been made, press the

buttons

once so that the on-screen

›

cursor is next to the RETURN TOMENU

line and press the Set button

. If you have

no other adjustments to make, press the OSD

button

to exit the menu system.

Multiroom Operation

When operating the AVR 4000 from a remote

room location where an IR sensor link has been

connected to the AVR 4000’s rear panel

Multiroom IR Input

, you may use either

the Main remote control or the Zone II remote.

To turn on the multiroom feed, press any of the

Input Selector buttons on the Zone II remote

∫ç∂

or the Main remote

456

Press the AVR Selector

∫

to turn the

unit on to the last source, or any of the other

Selector buttons to turn on to a specific source.

As long as an IR feed to the AVR 4000 has been

established from the remote room, using any of

the buttons on either remote will control the

remote location volume

, change the

tuner frequency u

, change the tuner

preset

or mute the output

If the Remote IR Output jack

on the AVR

4000 is connected to an IR Input jack on com-

patible Harman Kardon audio components such

as CD, DVD or cassette players, the transport

functions of those machines may also be

controlled using the Transport Controls

Éƒ©˙∆

on either remote

control.

To turn the system off from the remote room,

press the Power-Off button

Remember that the AVR 4000 may be turned on

or off from the remote room regardless of the

system’s operation or status in the main room.

NOTE: When the tuner is selected as the source

for the remote zone, any change to the frequen-

cy or preset will also change the station being

listened to in the main room, if the tuner is in

use there. Similarly, if someone in the main room

changes the station, the change will also impact

the remote room.

To activate the feed to the remote room, press

the Multiroom button

on the remote.

Next, press the Set button

. Press the

⁄

buttons

to turn the multiroom feed on or

off.When the multiroom system is on, the Multi

indicator

will light in the Main Information

Display

, and the Main Information

Display

or OSD will display MULTI ON.

Press the Set button twice

to enter the set-

ting.

When the multiroom system is turned on, the

input selected using the Multiroom Menu will be

fed to the Multiroom Output jacks

on the

rear panel.The volume will be as set in the same

menu, although it may also be adjusted using an

optional IR sensor and the Zone II remote in the

remote location or on the optional audio power

amplifier connected to the Multiroom Output

jacks

Once the multiroom system is turned on, it will

remain on even if the AVR 4000 is placed in the

Standby mode in the main room by pressing the

Power Off Button

or the System Power

Control

on the front panel. To turn off the

multiroom system from the main listening room,

even when the AVR is in Standby mode, press

the Multiroom button

and then the Set

button

. Press the

⁄

buttons

so that

the Multi indicator

in the Main

Information Display

goes out, and the

Main Information Display

or OSD will

display MULTI OFF.

Even when the AVR is turned off (to Standby

mode) and the Multiroom system is turned off

too, the multiroom system may be turned on at

any time from any room by pressing any of the

Selector buttons

456

∫ç∂

the remote in the remote room.

* MULTI-ROOM SETUP *

MULTI-ROOM:OFF ON

MULTI IN :FM PRESET 01

MULTI VOL :25dB

RETURN TO MENU

i need circuit diagram for avr 4000 to repair the safety mood Submitted on 1-1-2023 at 14:31
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 4000 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 4000

Harman Kardon AVR 4000 User Manual - Dutch - 58 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR 4000 Manual

Product: