Manual Harman Kardon AVR 4000 (page 36 of 58) (English)

8518

Zoom out

Zoom in

1/58

36 ADVANCED FEATURES

The AVR 4000 is equipped with a number of

advanced features that add extra flexibility to

the unit’s operation.While it is not necessary to

use these features to operate the unit, they pro-

vide additional options that you may wish to

use.

Display Brightness

The AVR 4000’s front panel Main Information

Display

is set at a default brightness level

that is sufficient for viewing in a normally lit

room. However, in some home theater installa-

tions, you may wish to occasionally lower the

brightness of the display, or turn it off completely.

To change the display brightness setting for a

specific listening session, you will need to make

an adjustment in the ADVANCED

SELECT menu. To start the adjustment,

press the OSD button

to bring the MAS-

TER MENU to the screen. Press the

⁄

Button

twice, until the on-screen

›

cursor is

next to the ADVANCED line. Press the Set

Button

to enter the ADVANCED

SELECT menu (Figure 9).

Figure 9

To change the brightness setting, at the

ADVANCED SELECT menu, make cer-

tain that the on-screen

›

cursor is next to the

VFDline, and press the

›

Button

until

the desired brightness level is highlighted in the

video display. When FULLis highlighted, the

display is at its normal brightness. When

HALF is highlighted, the display is at half the

normal brightness level. When OFF is high-

lighted, all of the indicators in the Main

Information Display

will go dark. Note,

however, that the green LEDs for the Input

Indicators



and the Surround Mode

Indicators

, as well as for the Power

Indicator

, will always remain lit to remind

you that the unit is turned on.

If you wish to make other adjustments in the

menu, press the

⁄

Buttons

until the on-

screen

›

cursor is next to the desired setting or

the RETURN TOMENUline and press

the Set button

. If you have no other adjust-

ments to make, press the OSD Button

exit the menu system.

The display brightness may also be changed by

pressing and holding the Set button

on the

front for three seconds until the message in the

Main Information Display

reads VFD

FULL. Within five seconds, press the front

panel Selector buttons

until the desired

brightness display level is shown. At that point,

press the Set button

again to enter the

setting.

Once the desired brightness level is selected, it

will remain in effect until it is changed again or

until the unit is turned off.

Turn On Volume Level

As is the case with most audio/video receivers,

when the AVR 4000 is turned on, it will always

return to the volume setting in effect when the

unit was turned off. However, you may prefer to

always have the AVR 4000 turn on at a specific

setting, regardless of what was last in use when

the unit was turned off.To change the default

condition so that the same volume level is

always used at turn-on, you will need to make

an adjustment in the ADVANCED

SELECT menu. To start the adjustment,

press the OSD button

to bring the MAS-

TER MENU (Figure 1) to the screen. Press

the

⁄

button

twice, until the on-screen

›

cursor is next to the ADVANCED line. Press

the Set button

to enter the

ADVANCED SELECT menu (Figure 9).

At the ADVANCED SELECT menu

make certain that the on-screen

›

cursor is next

to the volume default line by pressing the

⁄

buttons

as needed. Next, press the

›

but-

ton

so that the word ONis highlighted in

the video display. Next, press the

button

once so that the on-screen

›

cursor is next to

the DEFAULT VOLSET line.To set the

desired turn-on volume, press the

‹

›

buttons

or hold them pressed until the desired

volume level is shown on the DEFAULT

VOLSETline. Note that this setting may

NOT be made with the regular volume controls.

NOTE: Since the setting for the turn-on volume

cannot be heard while the setting is being made,

you may wish to determine the setting before

making the adjustment. To do this, listen to any

source and adjust the volume to the desired

level using the regular volume controls

. When the desired volume level to

be used at turn-on is reached, make a note of

the setting as it appears in the lower third of the

video screen or in the Main Information

Display

(a typical volume level will appear

as a negative number such as -25dB). When

making the adjustment, use the

‹

›

buttons

to enter this setting.

Unlike some of the other adjustments in this

menu, the turn-on volume default will remain in

effect until it is changed or turned off in this

menu, even when the unit is turned off com-

pletely.

If you wish to make other adjustments in the

menu, press the

⁄

Buttons

until the on-

screen

›

cursor is next to the desired setting or

the RETURN TOMENUline and press

the Set button

. If you have no other adjust-

ments to make, press the OSD Button

exit the menu system.

* ADVANCED SELECT *

VFD :FULL HALF OFF

VOLUME DEFAULT:OFF ON

DEFAULT VOL SET:25dB

SEMI OSD :OFF ON

SEMI OSD TIME OUT: 35

FULL OSD TIME OUT:205

RETURN TO MENU

Advanced Features

i need circuit diagram for avr 4000 to repair the safety mood Submitted on 1-1-2023 at 14:31
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 4000 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 4000

Harman Kardon AVR 4000 User Manual - Dutch - 58 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR 4000 Manual

Product: