Manual Harman Kardon AVR 4000 (page 12 of 58) (English)

8518

Zoom out

Zoom in

1/58

12 MAIN REMOTE CONTROL FUNCTIONS

Main Remote Control Functions

IMPORTANT NOTE: The AVR 4000’s remote

may be programmed to control up to seven

devices, including the AVR 4000. Before using

the remote, it is important to remember to press

the Input Selector button

that corre-

sponds to the unit you wish to operate. In addi-

tion, the AVR 4000’s remote is shipped from the

factory to operate the AVR 4000 and most

Harman Kardon CD or DVD players and cassette

decks. The remote is also capable of operating a

wide variety of other products using the control

codes that are part of the remote or by learning

commands from other remotes. Before using the

remote with other products, follow the instruc-

tions on pages 39 to program the proper codes

for the products in your system.

It is also important to remember that many of the

buttons on the remote take on different func-

tions, depending on the product selected using

the Input Selectors. The descriptions shown here

primarily detail the functions of the remote when

it is used to operate the AVR 4000. (See page 44

for information about alternate functions for the

remote’s buttons.)

Power On Button: Press this button to

turn on the power to a device selected by pressing

one of the Input Selectors

(except Tape).

IR Transmitter Window: Point this window

towards the AVR 4000 when pressing buttons on

the remote to make certain that infrared com-

mands are properly received.

Program/SPL Indicator: This three-color

indicator is used to guide you through the

process of programming the remote or learning

commands from a remote into the AVR 4000’s

remote code memory and it is also used as a

level indicator when using the remote’s EzSet

capabilities. (See page 25 for more information

on setting output levels, and see page 39 for

information on programming the remote.)

Power Off Button: Press this button to

place the AVR 4000 or a selected device unit in

the Standby mode. Note that when the AVR 4000

is switched off this will turn off the main room

functions, but if the Multiroom system is activat-

ed, it will continue to function.

Input Selectors: Pressing one of these

buttons will perform three actions at the same

time. First, if the AVR is not turned on, this will

power up the unit. Next, it will select the source

shown on the button as the input to the AVR.

Finally, it will change the remote control so that

it controls the device selected. After pressing one

of these buttons you must press the AVR

Selector button

again to operate the

AVR’s functions with the remote.

AVR Selector: Pressing this button will

switch the remote so that it will operate the AVR’s

functions. If the AVR is in the Standby mode, it will

also turn the AVR on.

AM/FM Tuner Select: Press this button to

select the AVR’s tuner as the listening choice.

Pressing this button when the tuner is in use will

select between the AM and FM bands.

Learn Button: Press this button to begin

the process of “learning” the codes from another

product’s remote into the AVR 4000’s remote.

(See page 40 for more information on using the

remote’s learning function.)

Test Tone: Press this button to begin the

sequence used to calibrate the AVR 4000’s output

levels. (See page 40 for more information on

calibrating the AVR 4000.)

Sleep Button: Press this button to place

the unit in the Sleep mode. After the time shown

in the display, the AVR 4000 will automatically

go into the Standby mode. Each press of the

button changes the time until turn-off in the fol-

lowing order:

Hold the button pressed for two seconds to turn

off the Sleep mode setting.

Note that this button is also used to change

channels on your TV, VCR and SAT receiver when

selected.

Surround Mode Selector: Press this but-

ton to begin the process of changing the sur-

round mode. After the button has been pressed,

use the

⁄

buttons

to select the desired

surround mode (See page 29 for more informa-

tion). Note that this button is also used to tune

channels when the TV, VCR and SAT receiver is

selected using the Input Selector

Night Mode: Press this button to activate

the Night mode. This mode is available only with

Dolby Digital encoded digital sources, and it pre-

serves dialog (center channel) intelligibilty at low

volume levels (See page 31 for more informa-

tion).

Channel Select Button: This button is

used to start the process of setting the AVR

4000’s output levels with an external source.

Once this button is pressed, use the

⁄

but-

tons

to select the channel being adjusted,

then press the Set button

, followed by the

⁄

buttons again, to change the level setting.

(See page 32 for more information.)

⁄

Buttons: These are multi-purpose

buttons. They will be used most frequently to

select a surround mode. To change the surround

mode, first press the SURR/CH

button

Next press these buttons to scroll up or down

through the list of surround modes that appear

in the Main Information Display

. These

buttons are also used to increase or decrease

output levels when configuring the unit with

either the internal test tone or an external

source. They are also used to enter delay time

settings after the Delay button

has been

pressed.

When the AVR 4000 remote is being programmed

for the codes of another device, these buttons are

also used in the “Auto Search” process (See page

39 for more information on programming the

remote.)

‹

Button: This button is used to change

the menu selection or setting during some of the

setup procedures for the AVR.

Set Button: This button is used to enter

settings into the AVR 4000’s memory. It is also

used in the setup procedures for delay time,

speaker configuration and channel output level

adjustment.

Digital Select: Press this button to assign

one of the digital inputs

RS#%

to a

source. (See page 30 for more information on

using digital inputs.)

Numeric Keys: These buttons serve as a

ten-button numeric keypad to enter tuner preset

positions. They are also used to select channel

numbers when TV, VCR or Sat receiver has

been selected on the remote, or to select track

numbers on a CD, DVD or LD player, depending

on how the remote has been programmed.

Tuner Mode: Press this button when the

tuner is in use to select between automatic tun-

ing and manual tuning. When the button is

pressed so that the AUTO indicator

goes

out, pressing the Tuning buttons

≠

will move the frequency up or down in single-

step increments. When the FM band is in use

and the AUTO indicator

is on, pressing this

button will change to monaural reception mak-

ing even week stations audible. (See page 33 for

more information.)

min

OFF

i need circuit diagram for avr 4000 to repair the safety mood Submitted on 1-1-2023 at 14:31
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 4000 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 4000

Harman Kardon AVR 4000 User Manual - Dutch - 58 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR 4000 Manual

Product: