Manual Harman Kardon AVR 4000 (page 13 of 58) (English)

8518

Zoom out

Zoom in

1/58

MAIN REMOTE CONTROL FUNCTIONS 13

Direct Button: Press this button when the

tuner is in use to start the sequence for direct

entry of a station’s frequency.After pressing the

button simply press the proper Numeric Keys

to select a station (See page 33 for more

information on the tuner).

Tuning Up/Down:When the tuner is in

use, these buttons will tune up or down through

the selected frequency band. If the Tuner Mode

button

has been pressed or the Band but-

ton

on the front panel was held pressed so

that the AUTO indicator

is illuminated,

pressing either of the buttons will cause the

tuner to seek the next station with acceptable

signal strength for quality reception. When the

AUTO indicator

is NOT illuminated, pressing

these buttons will tune stations in single-step

increments. (See page 33 for more information.)

OSD Button: Press this button to activate

the On Screen Display (OSD) system used to set

up or adjust the AVR 4000’s parameters.

Macro Buttons: Press these buttons

to store or recall a “Macro”, which is a

pre-programmed sequence of commands

stored in the remote. (See page 41 for more

information on storing and recalling macros.)

Transport Buttons: These buttons do not

have any functions for the AVR, but they may be

programmed for the forward/reverse play opera-

tion of a wide variety of CD or DVD players, and

audio or video- cassette recorders. (See page 39

for more information on programming the

remote.)

Skip Up/Down Buttons: These buttons

do not have a direct function with the AVR

4000, but when used with a compatibly pro-

grammed CD or DVD changer they will change

the tracks on the disc currently being played in

the changer.

RDS Select Button: Press this button to

display the various messages that are part of the

RDS data system of the AVR 4000’s tuner. (See

page 34 for more information on RDS).

Preset Up/Down: When the tuner is in

use, press these buttons to scroll through the

stations programmed into the AVR 4000’s mem-

ory. When CD or DVD is selected using the

Input Selector button

, these buttons may

function as Slow Fwd/Rev (DVD) or ”+10” (CD).

Clear Button: Press this button to clear

incorrect entries when using the remote to

directly enter a radio station’s frequency.

Memory Button: Press this button to enter

a radio station into the AVR 4000’s preset

memory. After pressing the button the MEMORY

indicator

will flash; you then have five sec-

onds to enter a preset memory location using

the Numeric Keys

. (See page 33 for more

information.)

Delay/Prev Ch.: Press this button to begin

the process for setting the delay times used by

the AVR 4000 when processing surround sound.

After pressing this button, the delay times are

entered by pressing the Set button

and

then using the

⁄

buttons

to change the

setting. Press the Set button again to complete

the process. (See page 23 for more information.)

›

Button: Press this button to change a set-

ting or selection when configuring many of the

AVR’s settings.

Speaker Select: Press this button to

begin the process of configuring the AVR

4000’s Bass Management System for use with

the type of speakers used in your system. Once

the button has been pressed, use the

⁄

but-

tons

to select the channel you wish to set

up. Press the Set button

and then select

the speaker type (see page 21 for more infor-

mation.)

Multi-Room: Press this button to activate

the Multiroom system or to begin the process of

changing the input or volume level for the sec-

ond zone. (See page 38 for more information on

the Multiroom system.)

Volume Up/Down: Press these buttons to

raise or lower the system volume.

TV/Video Button: This button does not

have a direct function on the AVR 4000, but

when used with a compatibly programmed VCR,

DVD or satellite receiver that has a “TV/Video”

function, pressing this button will switch

between the output of the player or receiver and

the external video input to that player. Consult

the Owner’s Manual for your specific player or

receiver for the details of how it implements this

function.

SPL Indicator Select: This button acti-

vates the AVR 4000’s EzSet function to quickly

and accurately calibrate the AVR 4000’s output

levels. Press and hold the button for three sec-

onds and then release it. Note that the Test Tone

will begin circulating, and the Program

Indicator

will change colors. During this

sequence, EzSet will automatically adjust the

output levels for all channels until they are

equal, as shown by the Program Indicator

lighting green for each channel. (See page 25

for more information on EzSet.)

6-Ch. Direct Input: Press this button to

select the component connected to the 6-Ch.

Direct Input

as the source

Mute: Press this button to momentarily

silence the AVR 4000 or TV set being controlled,

depending on which device has been selected.

When the AVR 4000 remote is being programmed

to operate another device, this button is pressed

with the Input Selector button

to begin

the programming process. (See page 39 for more

information on programming the remote.)

EzSet Sensor Microphone: The sensor

microphone for the EzSet microphone is behind

these slots. When using the remote to calibrate

speaker output levels using EzSet, be sure that

you do not hold the remote in a way that covers

these slots. (See page 25 for more information

on using EzSet).

NOTE: As any of the remote buttons pressed is

active with the device selected, the correspon-

ding Selector button

will briefly flash

red to confirm your selection.

Main Remote Control Functions

i need circuit diagram for avr 4000 to repair the safety mood Submitted on 1-1-2023 at 14:31
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 4000 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 4000

Harman Kardon AVR 4000 User Manual - Dutch - 58 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR 4000 Manual

Product: