Manual Harman Kardon AVR 165 (page 11 of 42) (English)

502592

Zoom out

Zoom in

1/42

AVR 1650/AVR 165

ENGLISH

Types of Home Theater System Connections

There are different types of audio and video connections used to connect the AVR to your

speakers, your TV or video display, and your source devices. The Consumer Electronics

Association has established the CEA

color-coding standard.

Connection Color Guide Table

Analog Audio Connection Color

Front Left/Right White/Red

Center Green

Surround Left/Right Blue/Gray

Subwoofer Purple

Digital Audio Connection Color

Coaxial (input or output) Orange

Optical Input Black

Optical Record Output Gray

Analog Video Connection Color

Component Video Red/Green/Blue

Composite Video Yellow

Speaker Connections

Speaker cables carry an ampliﬁed signal from the AVR’s speaker terminals to each

loudspeaker. Each cable contains two wire conductors, or leads, that are differentiated

in some way, such as with colors or stripes.

The differentiation helps you maintain proper polarity, without which your system’s low-

frequency performance can suffer. Each speaker is connected to the AVR’s speaker-

output terminals using two wires, one positive (+) and one negative (–). Always connect

the positive terminal on the speaker, which is usually colored red, to the positive terminal

on the AVR, which is colored as indicated in the Connection Color Guide Table, above. The

negative terminals on the speakers and the AVR are black.

Your AVR uses binding-post speaker terminals that can accept bare-wire cables or

banana plugs. Bare-wire cables are installed as shown below:

1. Unscrew Cap 3. Tighten Cap2. Insert Bare Wire

Banana plugs are inserted into the hole in the middle of the terminal cap, as shown

below:

A. Tighten Cap B. Insert Banana Connector

into Hole in Cap

Always connect the colored (+) terminal on the AVR to the (+) terminal on the speaker

(usually red), and the black (–) terminal on the AVR to the (–) terminal on the speaker

(usually black).

IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or

the other terminal. Touching wires can cause a short circuit that can damage your

AVR or ampliﬁer.

Subwoofer Connections

The subwoofer is a speaker dedicated to reproducing only the low (bass) frequencies,

which require more power. To obtain the best results, most speaker manufacturers offer

powered subwoofers that contain their own ampliﬁers. Use a single RCA audio cable

(not included) to make a line-level (non-ampliﬁed) connection from the AVR’s Subwoofer

connector to a corresponding input jack on the subwoofer.

Although the AVR’s purple subwoofer output looks similar to a full-range analog audio

jack, it is ﬁltered so that only the low frequencies pass through it. Don’t connect this

output to any device other than a subwoofer.

Source Device Connections

Audio and video signals originate in source devices (components where a playback

signal originates) such as your Blu-ray Disc or DVD player, CD player, DVR (digital video

recorder) or other recorder, tape deck, game console, cable or satellite television tuner,

iPod or iPhone (docked in an optional The Bridge IIIP docking station) or MP3 player. The

AVR’s FM/AM tuner also counts as a source, even though no external connectors are

needed other than the AVR’s FM and AM antennas. Separate connectors are required

for the audio and video portions of the source device’s signal, except for digital HDMI

connectors. The types of connectors you use will depend upon the capabilities of the

source device and of your TV or video display.

Digital Audio Connections – HDMI

There are two types of audio connections – digital and analog. Digital audio signals are

required for listening to sources encoded with digital surround modes, such as Dolby

Digital and DTS, or for uncompressed PCM digital audio. Your AVR has three types of

digital audio connectors: HDMI, coaxial and optical. Do not use more than one type of

digital audio connector for each source device. However, it’s okay to make both analog

and digital audio connections to the same source.

Your AVR is equipped with four rear-panel HDMI input connectors and one HDMI monitor

output connector. HDMI technology enables digital audio and video information to be

carried using a single cable, delivering the highest quality picture and sound. If your TV

or video-display device has an HDMI input connector, make a single HDMI connection

from each source device to the AVR. Usually, a separate digital audio connection is not

required.

The AVR’s HDMI Monitor Output connector contains an Audio Return Channel (ARC) that

carries a digital audio signal from your TV or video display back to the AVR. It allows

you to listen to HDMI devices that are connected directly to your TV (such as an Internet

connection) without making an additional connection from the device to the AVR. The

ARC signal is active when the TV source is selected. See

System Setup,

on page 23, for

more information.

The HDMI connector is shaped for easy plug-in (see illustration, below), and HDMI cable

runs are limited to about 10 feet (3m). If your video display has a DVI input and is

HDCP-compliant, use an HDMI-to-DVI adapter (not included), and make a separate audio

connection.

Digital Audio Connections – Coaxial

Coaxial digital audio jacks are usually color-coded orange. Although they look like

standard RCA-type analog jacks, you should not connect coaxial digital audio outputs to

analog inputs or vice versa.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 165 in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 165

Harman Kardon AVR 165 User Manual - German - 42 pages

Harman Kardon AVR 165 User Manual - Dutch - 42 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR 165 Manual

Product: