Manual Harman Kardon AVR 110 (page 30 of 44) (English)

502582

Zoom out

Zoom in

1/44

30 PROGRAMMING THE REMOTE

Programming the Remote

2. Press the Play button w.The Program

Indicator

c will stop flashing and stay

amber.

3. Press and release the

Input Selector button

e for the device that will be used to change

the channels. The

Program Indicator c will

blink green three times and then go out to con-

firm the data entry.

Example: To control the transport of a DVD

player while the remote is set to control the TV,

first press the

VID 2/TV Input Selector but-

ton

e and the Mute button at the

same time. Next, release them and press the

Play button w, followed by the DVD Input

Selector

button e.

NOTE: To remove the Channel Control Punch-

Through and return the remote to its original con-

figuration, repeat the steps shown in the example

above. However, press the

VID 2/TV Input

Selector

in Steps 1 and 3.

NOTE: Before programming the remote for

Volume, Channel or Transport Punch-Through,

make certain that any programming needed for

the specific TV, CD, DVD, Cable or Satellite

Receivers has been completed.

Reassigning Device Control

Selectors

Although each Input Selector e is normally

assigned to the category of product shown on the

remote, it is possible to reassign one of these but-

tons to operate a second device of another type.

For example, if you have two VCRs but no satellite

receiver, you may program the “SAT” button to

operate a second VCR. Before following the nor-

mal programming steps for either Three-Digit entry

or Auto Search code entry, you must first reassign

the button with the following steps:

1. Press the

Input Selector e you wish to

reassign and the

Mute button at the

same time until the red light appears under the

Input Selector e and the Program

Indicator

c flashes amber.

2. Press the

Input Selector e for the device

you wish to program into the reassigned

button.

3. Enter the three-digit code for the specific

model you wish the reassigned button to

operate.

4. Press the same

Input Selector e pressed in

Step 1 once again to store the selection.The

red LED under the reassigned Input Selector will

flash three times and then go out.

Example: To use the CBL/SAT button to oper-

ate a second VCR, first press the

CBL/SAT

Input Selector

e and the Mute button

at the same time until the red light glows

under the

CBL/SAT e button. Press the VCR

e button, followed by the three-digit code

for the specific model you wish to control.

Finally, press the

CBL/SAT e button again.

Resetting the Remote Memory

As you add components to your home-theater sys-

tem, occasionally you may wish to totally repro-

gram the remote control without the confusion of

any commands, macros or ”Punch-Through“ pro-

gramming that you may have done. To do this, it is

possible to reset the remote to the original factory

defaults and command codes by following these

steps. Note, however, that once the remote is

reset, all commands or codes that you have

entered will be erased and will need to be re-

entered:

1. Press any of the

Input Selector buttons e

and the ”O“ button r at the same time until

the

Program Indicator c begins to flash

amber.

2. Press the

”3“ button r three times.

3.The red LED under the

Input Selector e will

go out and the

Program Indicator c will

stop flashing and turn green.

4.The

Program Indicator c will remain green

until the remote is reset. Note that this may

take a while, depending on how many com-

mands are in the memory and need to be

erased.

5.When the

Program Indicator c goes out,

the remote has been reset to the factory

settings.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 110 in the language / languages: English as an attachment in your email.

The manual is 0,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR 110 Manual

Product: