807621

Hapro HP 8580 Innergize Manual

6
Zoom out
Zoom in
Previous page
1/56
Next page
Resetting the operating hours counter
Follow these steps to clear the (symbol) symbol from the display:
1 Have the tanning lamps replaced by a VDL Hapro-authorised service centre.
2 Make sure the display is set to 00.
3 Press the buttons in the following sequence:
Start/stop button ( ), pause button ( ), pause button ( ), repeat button ( ), pause
button ( )
The symbol disappears from the display.
Other parts
Have the infrared lamps (1100W) and the UV lters replaced by a service centre authorised
by VDL Hapro. Only they have the knowledge and skills required for this job and the
original spare parts for the appliance.
- Have the infrared lamps replaced when they stop functioning.
- The UV lters protect against exposure to undesired UV light. It is therefore important to
have a damaged or broken lter replaced right away.
- If the mains cord is damaged, you must have it replaced by Philips, a service centre
authorised by VDL Hapro or similarly qualied persons in order to avoid a hazard.
Troubleshooting
If problems should arise with this appliance and you are unable to solve them by means of the
information below, please contact the nearest VDL Hapro dealer.
Problem Solution
The appliance does not
work.
The plug may not be inserted properly in the wall socket. Put the plug
properly in the wall socket.
There may be a power failure. Test if the power supply works by connecting
another appliance.
The tanning lamps may still be too hot to go on. Let them cool down for 3
minutes rst.
The overheat protection may have switched o the appliance
automatically because it overheated. Remove the cause of overheating
(e.g. a towel that blocks one or more vents). Let the appliance cool down
for a while and then switch the appliance back on.
Make sure the lamp unit is in the right position. See chapter ‘Preparing for
use’.
The top of the control
panel becomes hot during
use.
The lamps heat up the top of the control panel. This is normal.
The fuse of the circuit to
which the appliance is
connected cuts o the
power when I switch on or
use the appliance.
The fuse of the circuit to which the tanning appliance is connected must
be a 16A standard fuse or a slow-blow automatic fuse. You may also have
connected too many appliances to the same circuit.
ENGLISH8
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hapro HP 8580 Innergize at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hapro HP 8580 Innergize in the language / languages: English, German, Dutch, French, Italian, Spanish, Norwegian as an attachment in your email.

The manual is 0.61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info