495087
102
Zoom out
Zoom in
Previous page
1/112
Next page
*#1 :-Owner’s Manual
Appendix102
MIDI Information
Spring Shock
Status 2nd Byte 3rd Byte
Bn 10 vv
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
vv=Any:
Hold 1
Status 2nd Byte 3rd Byte
Bn 40 vv
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
vv=Control Value: 00 - 7F(0 - 127) 0-63 = Off, 64-127 = On
Pro
g
ram Chan
g
e
Status 2nd Byte
Cn pp
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
pp=Program Number
Upper Channel: Change Combination Preset.
Lower Channel: Change Lower Preset only.
Pitch Bend Chan
g
e
Status 2nd Byte 3rd Byte
En ll mm
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
mm=Upper Byte
ll=Lower Byte
00 00(-8192) - 40 00(0) - 7F 7F(8191)
[Channel Voice Message]
Note Off
Status 2nd Byte 3rd Byte
8n kk vv or
9n kk 00
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
kk=Note Number: 00 - 7F(0 - 127)
vv=Velocity(disregard): 00 - 7F(0 - 127)
Note On
Status 2nd Byte 3rd Byte
9n kk vv
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
kk=Note Number: 00 - 7F(0 - 127)
vv=Velocity: 00 - 7F(0 - 127)
Control Change
Program Change messages etc. are received.
Bank Select
Status 2nd Byte 3rd Byte
Bn 00 mm
Bn 20 ll
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
mm,ll=Bank Number: 00 00 - 7F 7F
Default Value = 00 00
However, when you send the Bank Select, be sure to send
both Upper Byte(mm) and Lower Byte(ll).
reserved.
Modulation
Status 2nd Byte 3rd Byte
Bn 01 vv
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
vv=Modulation Depth: 00 - 7F
Volume
Status 2nd Byte 3rd Byte
Bn 07 vv
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
vv=Volume: 00 - 7F(0 - 127)
Default Value = 64(100)
the received message.
The volume message is used to set the volume balance of each Ex. zone.
Pan
Status 2nd Byte 3rd Byte
Bn 0A vv
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
vv=Pan: 00(Left) - 40(Center) - 7F(Right)
Default Value = 40(64)
Expression
Status 2nd Byte 3rd Byte
Bn 0B vv
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
vv=Expression: 00 - 7F(0 - 127)
Default Value = 7F(127)
It controls the volume of the Part corresponding to the MIDI Channel of
The value set by the Control Change is not reset even when
This device process the Lower Byte (ll) of the Bank Number as 00.
Until you send the Program Change, the Bank Select process is
[Channel Mode messages]
All Sounds Off
Status 2nd Byte 3rd Byte
Bn 78 00
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
When this message is received, all currently-sounding notes on the
corresponding channel will be turned off immediately.
Reset All Controllers
Status 2nd Byte 3rd Byte
Bn 79 00
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
When this message is received, the following controllers will be set to
their reset values.
Controller Reset Value
Pitch Bend Change ±0 (Center)
Modulation 0 (off)
Expression 127 (Maximum)
Hold 1 0 (off)
RPN unset; previously set data will not change
NRPN unset; previously set data will not change
All Notes Off
Status 2nd Byte 3rd Byte
Bn 7B 00
n=MIDI Channel Number: 0 - F(Ch.1 - 16)
When All Notes Off is received, all notes on the corresponding channel
will be turned off. However if Hold 1 is On, the sound will be continued
until these are turned off.
102


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hammond XK-3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hammond XK-3 in the language / languages: English as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info