495084
115
Zoom out
Zoom in
Previous page
1/130
Next page
115
Frequently Asked Questions
Malfunction of the buttons, the keys, etc.
Turn off the POWER switch once, then turn it on again. If this procedure is not successful, turn off the
POWER switch. While pressing the [RECORD] button, turn the POWER switch on again. (Note that in this
case, all parameters return to their factory-preset status.)
No sound is produced when the keys are pressed.
The MASTER VOLUME is at the minimum setting.D
Adjust the volume with the MASTER VOLUME control. (P. 22 #25)
No Preset key is selected. D
Select a Preset key.
A plug is inserted to the HEADPHONE jack. D
While a plug is inserted here, the Leslie speaker is disabled.
The Foot Switch does not work.
The Foot Switch settings are not correct.D
Reset the Foot Switch correctly in the CONTROL mode. (P. 91 #4)
The sound does not come out immediately after switched on.
A Vacuum Tube circuit is mounted in this organ. It takes approximately 10 to 20 seconds after switched on
before you will hear the sound.
The sound is not distorted if the OVERDRIVE knob is turned.
When the Overdrive Expression is at “EX-OD”, it does not distort if the Expression pedal is low. In such a
case, increase the Expression pedal, or set the Overdrive Expression at “OD-EX” if you want to distort
regardless of the Expression value. (P. 80 #1)
Leslie speaker sound is distorted.
If the sound is distorted regardless of the position of the volume of the Leslie speaker when you are using a
Leslie adapter (such as the 11 pin/6 pin converter), the power of this organ seems to be so large that the sound
is distorted inside the Leslie adapter. In such a case, return the [MASTER VOLUME] knob to 10 o’clock
position.
The rotor of the external Leslie speaker does not stop, if the Leslie mode is switched
to [STOP].
Some Leslie Speaker models do not [STOP]. [STOP] is possible on 2101/2102, 122XB, 971 and 3300 (cur-
rent models).
Audio is interrupted when a Combination Preset is selected.
Between the Combination Presets with different Tonewheel Settings, the sound will be cut off while the
Tonewheel Settings are switched.
The sound is once cut between the presets with different key mode (MONO/POLY) on the Pedal part, for
switching the sound algorithm.
There is excessive MIDI latency compared to the organ (Drawbar) sound.
The position of the key contact for MIDI send is deeper than that of the multi-contacts for Drawbars.
There are too many zones to send. D
Turn [OFF] the switches of unnecessary external zones.
No sounds of Pedal part from the headphones.
PEDAL OUTPUT set at “PEDOUT”. D
Set the PEDAL OUTPUT at “BOTH” when using the headphones (P. 96 #1).
Manual contact does not work well.
The multi-contacts used for the manuals on this organ is designed to be used for a long time. Refer for the
contact refreshing procedures to the “Instruction for keyboard contact cleaning function”.
And, if all the contact points have been worn out and the problem is not solved any longer by refreshing the
contacts, please consult your local dealer or store for further maintenance.
TROUBLESHOOTING
115


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hammond C-3 mk2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hammond C-3 mk2 in the language / languages: English as an attachment in your email.

The manual is 6,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info