655938
15
Zoom out
Zoom in
Previous page
1/25
Next page
14
Selecteer met de Programma toetsen uw lengte. Bevestig met
ENTER
, de volgende waarde zal geactiveerd worden.
Selecteer met de Programma toetsen uw leeftijd. Bevestig met
ENTER
en de vetpercentagemeting zal starten.
Als de meting klaar is zal het vetpercentage op het display
getoond worden. Om de Bodyfat-Modus te verlaten, drukt u op
STOP.
Voor een correcte meting moeten beide handen op de
harstlagsensoren geplaatst worden
!
.
Select by pressing the +/- buttons your bodyheight. Done,
press
ENTER
and the next section
will
be activated.
Select by pressing the +/- buttons your age. Done, press ENTER
and all settings are confirmed..
After all setting, The
LCD will twinkle
and then hold both of your
hands on the hand pulse to test your body fat. The
LCD will
show your body fat when test is finished.
Press
STOP
to exitt.
6. Verzorging en onderhoud
6. Care and Maintenance
6.1 Verzorging
Gebruik voor het schoonmaken van de loopband een
stofzuiger. Alleen als de band erg vies is, kunt u een natte
doek gebruiken. Gebruik geen reinigingsmiddel.
Voor het schoonmaken van het frame/display kunt u een
vochtige doek gebruik. Vermijd het gebruik van
agressieve reinigingsmiddelen en zorg dat er geen
vloeistof in de computer kan binnendringen.
Onderdelen die in contact komen met zweet kunt u met
een vochtige doek schoonmaken.
6.2 Centreren van de loopband
Tijdens het trainen kan het gebeuren dat uw ene voet
harder neerkomt dan uw andere voet. Dit kan ervoor
zorgen dat de loopband niet meer gecentreerd in het
midden ligt. Normaal gesproken zal de loopband
automatisch terug gecentreerd worden. Na langdurig
gebruik kan het echter voorkomen dat dit niet meer
automatisch gebeurt
.
In dat geval moet u de loopband met de 2 inbus
schroeven centreren. Trek niet al te wijd zittende
kleding aan tijdens deze werkzaamheden.
-
Draai de inbusschroef per keer niet meer dan 1x
volledig rond.
-
Strek de ene zijde en maak de andere zijde los
.
-
Laat tijdens het centreren de loopband met een
snelheid van ca. 6km/hr lopen zonder dat er iemand
op staat.
Als u klaar bent met centreren, loop dan zelf gedurende 5
minuten op de loopband met een snelheid van ca.6km/hr.
Als de loopband nog steeds niet goed ligt, herhaal dan
bovenstaande stappen. Let op dat u de loopband niet teveel
forceert, doet u dat wel dan kan dat een kortere levensduur
van de band tot gevolg hebben.
Als de band teveel afwijkt van de linker zijkant,
-
draai dan de linker schroef 1 slag met de klok mee
(vaster zetten)
-
draai dan de rechter schroef 1 slag tegen de klok in
(losser draaien)
Als de band teveel afwijkt van de rechter zijkant:
-
draai dan de linker schroef 1 slag tegen de klok in
(losser draaien)
-
draai dan de rechter schroef 1 slag met de klok mee
(vaster zetten)
6.1
Care
For cleaning the running belt use a vacuum cleaner.
If
the belt is really
dirty,
please use a wet cloth. Do not
use
any
cleanser.
When cleaning, use only a moist cloth and avoid
harsh
cleaning agents. Ensure that no moisture
comes
into the
computer.
Components that come into contact with
perspiration,
need cleaning
only
with a damp cloth.
6.2 Centering the running belt
During the exercise, one foot is pushing the running belt
stronger
than the other. According to that, the belt
will
be
moved out of the centre.
Normlly
the belt
will
be
centred
automatically, but during longer exercise, it can be,
that
the
belt is
off
the centre.In this case, please
follow
up
the
following
instruction. At the rear end of the running
deck, there are 2pcs of allen screws, which
will
be
used
for centering the belt. Don´t use any loose clothes during
centering.
-
Please turn the allen screw not more than
¼
turn for
each
step.
-
Stretch one side and release the other side.
-
the speed of the belt has to be
6km/h,
but
make
sure, that nobody is running on the belt.
If
you
finish
the centering,
walk
on the treadmill for about
5
minutes, with the speed of
6km/h.
If
the running belt is still
not in centre, please centre the belt again. Pay
attention,
that you don´t force the belt too much, a
shorter
life will
be
caused.
If
the gap on the left side is too big,
please
-
turn the left screw a
¼
turn clockwise (tighten it)
-
turn the right screw a
¼
turn anticlockwise (loose it)
If
the gap on the right side is too big,
please
-
turn the left screw a
¼
turn anticlockwise (loose it)
-
turn the right screw a
¼
turn clockwise (tighten it)
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hammer 4326 LR16i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hammer 4326 LR16i in the language / languages: English, Dutch as an attachment in your email.

The manual is 5,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hammer 4326 LR16i

Hammer 4326 LR16i User Manual - English, German - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info