683782

Hako Scrubmaster B140R Manual

5
Zoom out
Zoom in
Previous page
1/38
Next page
The machine must not be operated in
areas endangered by risks of explosion.
The machine may be used only for
hard floorings in indoor areas and for
operation on plane areas with a maxi-
mum inclination of up to 2%.
Driving e.g. on ramps with a maximum
inclination of 10% is only allowed for
transportation. Uphill drive must not
exceed 1 minute and particular care
has to be taken.
Repair, maintenance and cleaning
work must only be performed if the
master key is removed.
Before working on the electrical system,
be sure to disconnect the battery
plug.
Taking other persons than the opera-
tor with the Hakomatic is not allowed.
If the Hakomatic is equipped with a
driver seat, it may only be turned on
when the operator is seated (seat
switch).
A perfect maintenance of the machine
mainly helps preventing accidents.
When performing repair, maintenance,
setting or other work the appropriate
tools have to be used. Other spare
parts than the genuine Hako spare
parts must at least equal the original
parts as far as the safety standards
are concerned.
The Hakomatic B 910 has to be chek-
ked by an expert in regular inter-
37
intervals for its proper and safe opera-
tion (we recommend a check once
yearly at least) and after modification
or repair.
The Hakomatic must be equipped
by brushes and pads as requires the
manufacturer (refer to section ”Tech-
nical data”). Using other brushes/pads
than indicated affects your safety.
Do not clean the machine by means
of vapor jet or high pressure cleaning
equipment.
For an increased danger of tilting, the
pneumatic tire equipment of the Hako-
matic is not admissible.
Do not allow water to enter any elec-
trical parts.
The machine is splash proof (IPX3).
Do not allow water to get in the ma-
chine in the driver’s seat area as it
may be collected on the battery stored
below the seat, remove water if
required.
Particular instructions for safe
handling of batteries
(See enclosed leaflet 88-60-2556)
Notes on warranty
The terms of the sales contact apply.
Damages are not subject to warranty
if they are due to non-compliance with
the maintenance and service provi-
sions. Any maintenance work has to
be performed by an authorized Hako
service work-shop and confirmed in
the „maintenance certificate“ which is
the warranty document.
The following is excluded from war-
ranty:
natural wear and tear after overload,
fuses and damages caused by inex-
pent handling and unauthorized modi-
fication of the machine.
Moreover, any claim for warranty be-
comes extinct if damages at the ma-
chine are caused by fitting of parts or
accessories without Hako’s prior and
explicit consent or by noncompliance
with the maintenance instructions.
The machine must not be operated in
areas endangered by risks of explosion.
The machine may be used only for
hard floorings in indoor areas and for
operation on plane areas with a maxi-
mum inclination of up to 2%.
Driving e.g. on ramps with a maximum
inclination of 10% is only allowed for
transportation. Uphill drive must not
exceed 1 minute and particular care
has to be taken.
Repair, maintenance and cleaning
work must only be performed if the
master key is removed.
Before working on the electrical system,
be sure to disconnect the battery
plug.
Taking other persons than the opera-
tor with the Hakomatic is not allowed.
If the Hakomatic is equipped with a
driver seat, it may only be turned on
when the operator is seated (seat
switch).
A perfect maintenance of the machine
mainly helps preventing accidents.
When performing repair, maintenance,
setting or other work the appropriate
tools have to be used. Other spare
parts than the genuine Hako spare
parts must at least equal the original
parts as far as the safety standards
are concerned.
The Hakomatic B 910 has to be chek-
ked by an expert in regular inter-
37
intervals for its proper and safe opera-
tion (we recommend a check once
yearly at least) and after modification
or repair.
The Hakomatic must be equipped
by brushes and pads as requires the
manufacturer (refer to section ”Tech-
nical data”). Using other brushes/pads
than indicated affects your safety.
Do not clean the machine by means
of vapor jet or high pressure cleaning
equipment.
For an increased danger of tilting, the
pneumatic tire equipment of the Hako-
matic is not admissible.
Do not allow water to enter any elec-
trical parts.
The machine is splash proof (IPX3).
Do not allow water to get in the ma-
chine in the driver’s seat area as it
may be collected on the battery stored
below the seat, remove water if
required.
Particular instructions for safe
handling of batteries
(See enclosed leaflet 88-60-2556)
Notes on warranty
The terms of the sales contact apply.
Damages are not subject to warranty
if they are due to non-compliance with
the maintenance and service provi-
sions. Any maintenance work has to
be performed by an authorized Hako
service work-shop and confirmed in
the „maintenance certificate“ which is
the warranty document.
The following is excluded from war-
ranty:
natural wear and tear after overload,
fuses and damages caused by inex-
pent handling and unauthorized modi-
fication of the machine.
Moreover, any claim for warranty be-
comes extinct if damages at the ma-
chine are caused by fitting of parts or
accessories without Hako’s prior and
explicit consent or by noncompliance
with the maintenance instructions.
The machine must not be operated in
areas endangered by risks of explosion.
The machine may be used only for
hard floorings in indoor areas and for
operation on plane areas with a maxi-
mum inclination of up to 2%.
Driving e.g. on ramps with a maximum
inclination of 10% is only allowed for
transportation. Uphill drive must not
exceed 1 minute and particular care
has to be taken.
Repair, maintenance and cleaning
work must only be performed if the
master key is removed.
Before working on the electrical system,
be sure to disconnect the battery
plug.
Taking other persons than the opera-
tor with the Hakomatic is not allowed.
If the Hakomatic is equipped with a
driver seat, it may only be turned on
when the operator is seated (seat
switch).
A perfect maintenance of the machine
mainly helps preventing accidents.
When performing repair, maintenance,
setting or other work the appropriate
tools have to be used. Other spare
parts than the genuine Hako spare
parts must at least equal the original
parts as far as the safety standards
are concerned.
The Hakomatic B 910 has to be chek-
ked by an expert in regular inter-
37
intervals for its proper and safe opera-
tion (we recommend a check once
yearly at least) and after modification
or repair.
The Hakomatic must be equipped
by brushes and pads as requires the
manufacturer (refer to section ”Tech-
nical data”). Using other brushes/pads
than indicated affects your safety.
Do not clean the machine by means
of vapor jet or high pressure cleaning
equipment.
For an increased danger of tilting, the
pneumatic tire equipment of the Hako-
matic is not admissible.
Do not allow water to enter any elec-
trical parts.
The machine is splash proof (IPX3).
Do not allow water to get in the ma-
chine in the driver’s seat area as it
may be collected on the battery stored
below the seat, remove water if
required.
Particular instructions for safe
handling of batteries
(See enclosed leaflet 88-60-2556)
Notes on warranty
The terms of the sales contact apply.
Damages are not subject to warranty
if they are due to non-compliance with
the maintenance and service provi-
sions. Any maintenance work has to
be performed by an authorized Hako
service work-shop and confirmed in
the „maintenance certificate“ which is
the warranty document.
The following is excluded from war-
ranty:
natural wear and tear after overload,
fuses and damages caused by inex-
pent handling and unauthorized modi-
fication of the machine.
Moreover, any claim for warranty be-
comes extinct if damages at the ma-
chine are caused by fitting of parts or
accessories without Hako’s prior and
explicit consent or by noncompliance
with the maintenance instructions.
The machine must not be operated in
areas endangered by risks of explosion.
The machine may be used only for
hard floorings in indoor areas and for
operation on plane areas with a maxi-
mum inclination of up to 2%.
Driving e.g. on ramps with a maximum
inclination of 10% is only allowed for
transportation. Uphill drive must not
exceed 1 minute and particular care
has to be taken.
Repair, maintenance and cleaning
work must only be performed if the
master key is removed.
Before working on the electrical system,
be sure to disconnect the battery
plug.
Taking other persons than the opera-
tor with the Hakomatic is not allowed.
If the Hakomatic is equipped with a
driver seat, it may only be turned on
when the operator is seated (seat
switch).
A perfect maintenance of the machine
mainly helps preventing accidents.
When performing repair, maintenance,
setting or other work the appropriate
tools have to be used. Other spare
parts than the genuine Hako spare
parts must at least equal the original
parts as far as the safety standards
are concerned.
The Hakomatic B 910 has to be chek-
ked by an expert in regular inter-
37
intervals for its proper and safe opera-
tion (we recommend a check once
yearly at least) and after modification
or repair.
The Hakomatic must be equipped
by brushes and pads as requires the
manufacturer (refer to section ”Tech-
nical data”). Using other brushes/pads
than indicated affects your safety.
Do not clean the machine by means
of vapor jet or high pressure cleaning
equipment.
For an increased danger of tilting, the
pneumatic tire equipment of the Hako-
matic is not admissible.
Do not allow water to enter any elec-
trical parts.
The machine is splash proof (IPX3).
Do not allow water to get in the ma-
chine in the driver’s seat area as it
may be collected on the battery stored
below the seat, remove water if
required.
Particular instructions for safe
handling of batteries
(See enclosed leaflet 88-60-2556)
Notes on warranty
The terms of the sales contact apply.
Damages are not subject to warranty
if they are due to non-compliance with
the maintenance and service provi-
sions. Any maintenance work has to
be performed by an authorized Hako
service work-shop and confirmed in
the „maintenance certificate“ which is
the warranty document.
The following is excluded from war-
ranty:
natural wear and tear after overload,
fuses and damages caused by inex-
pent handling and unauthorized modi-
fication of the machine.
Moreover, any claim for warranty be-
comes extinct if damages at the ma-
chine are caused by fitting of parts or
accessories without Hako’s prior and
explicit consent or by noncompliance
with the maintenance instructions.
Scrubmaster is not allowed.
Scrubmaster is equipped with a
Scrubmaster B140 R has to be chek-
Scrubmaster must be equipped
Scrub-
master B140 R is not admissible.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hako Scrubmaster B140R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hako Scrubmaster B140R in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info