683781
6
Zoom out
Zoom in
Previous page
1/32
Next page
EN
EN-4
1.1 INTRODUCTION
The manual is an integral part of the machine
itself; it must therefore be stored carefully in a
safe place which is accessible to all users (oper-
ators and personnel in charge of maintenance)
for the entire machine life until demolition.
1.1.a - Purpose of the manual
The purpose of the manual is to provide the
instructions necessary for putting into serv-
ice, using and maintaining the machine with
which it is enclosed.
It is advisable to read the instructions care-
fully and comply with the safety standards
described in the manual to the letter.
The non-observance of these instructions/stand-
ards may cause damage to the machine and in-
jury to the operator for which under no circum-
stances is the manufacturer responsible.
The safety information described in the man-
ual supplements and DOES NOT REPLACE
standards in force in the country in which the
machine is used.
1.1.b - Consulting the manual
The manual is divided into chapters accord-
ing to a logical order of knowledge and use
of the machine.
For help with finding a specific topic, first
consult the CONTENTS shown at the begin-
ning of the manual.
1.1.c - Key to symbols used in the
manual
In order to highlight information and proce-
dures regarding safety, maintenance etc.,
the following symbols have been adopted in
the manual:
DANGER:
Warns of a serious, even fatal danger for
the safety of the operator and/or third per-
sons.
WARNING:
Extremely important information in or-
der to prevent serious damage to the
machine and the environment in which it
operates.
N.B.:
Additional information for correct machine
operation or of a general nature.
1.1.d - Conventional terminology
The terms front, rear, forward, back, upper,
lower, left and right refer to the operator in
the working position with his/her hands on
the guide handle.
To simplify, the brand name of the model has
been replaced with “Machine”.
The machine comes in two versions:
- BC: version with batteries
- E: version with electric cable
1.2 GENERAL
WARNINGS
Before putting into service, using and main-
taining the machine, it is necessary for the
persons involved (persons in charge and op-
erators) to be trained regarding the operating
procedures and safety standards shown in
this manual.
Respect all the provisions contained in the
manual and in any enclosed documentation.
DANGER:
It is forbidden for untrained personnel,
children and disabled persons to use the
machine.
1.2.a - Personnel qualifications
Operator
The term operator refers to a generic worker
able to perform simple operations such as
running the machine and carrying out the
relative cleaning at the end of the working
shift.
Electrical/mechanical maintenance technician
A technician qualified to operate on the ma-
chine in order to repair or replace parts which
require the removal of the protective cover.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hako Scrubmaster B12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hako Scrubmaster B12 in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info