656799

Haier Intelius 50 - HW80-B14266A Manual

22
Zoom out
Zoom in
Previous page
1/56
Next page
Problem Cause Solution
Operation stops
before completing
wash cycle
s Water or electric failure. s Check power and water supply
Operation stops for a
period of time
s Appliance displays error code.
s Problem due to load pattern.
s Programme performs soaking
cycle?
s Consider error code
s Reduce or adjust load.
s If it seems appropriate cancel
operation.
Excessive foam floats
drum and/or deter-
gent drawer.
s Detergent is not a appropriate
s Excessive use of detergent.
s Check detergent recommen-
dations.
s Reduce amount of detergent.
Automatic adjustment
of washing time.
s Washing programme duration
will be adjusted.
s This is normal and doesn‘t
affect functionality.
Spinning fails.
s Unbalance of laundry. s Check machine load and
laundry and run a spinning
programme again.
23
Installation
Preparation
Remove all packaging material including polystyrene base.
While opening the package, water drops may be seen on
plastic bag and porthole. This normal phenomenon results
from water tests in the factory.
Dispose of the packaging in an environmentally
friendly manner. For information refering current
disposal routes, consult your retailer or the local
authorities.
Optional: Adjusting the bottom cover
board
When opening the shrink package, you will find a calcium-
plastic board and a felt. The board is used for reducing
noise after covering the bottom of the cabinet.
1. Past the felt on one side of the calcium-plastic board
(figure.1).
2. Lay the washing machine down to its side, porthole
pointing upwards, bottom side towards operator and
screw off the four bolts. (figure 2).
3. Place the calcium-plastic board with felt towards inside,
screw the bolts through the four holes on the board
on to the tub firmly (figure 3). Finally set the machine
upright again.
Dismantle the transportation bolts
The transportation bolts are designed for clamping anti-
vibration components inside the appliance during trans-
portation to prevent inner damage.
4. Remove the back cover.
5. Remove bolts on the rear side and take out
plastic
spacers (A)
from inner side of the machine.
General information and tips:
Keep the transportation bolts in a safe place for later
use. Whenever the appliance is to be moved at first
reinstall the bolts.
3.
4.
1.
2.
5.
A
22
Troubleshooting
General information and tips:
If too much foam is inspected during spin cycle, motor stops and drain pump will be
activated for 90 seconds. If that elimination of foam fails up to 3 times, programme
ends without spinning.
Warning!
Electrical equipment should be serviced only by qualified electrical experts, because improper
repairs can cause considerable consequential damages.
If the supply cord is damaged, it must be replaced by the service agent (see warranty card) in
order to avoid a hazard.
In case of power failure
The current programme and its setting will be saved. When
power supply is restored operation will be resumed. To can-
cel it, touch “Start/Pause“ and then “Power“ for about 3 sec.
If a power failure cuts an operating wash programme door
opening is mechanically blocked. To get out any laundry water
level should not be seen in the glassy porthole of the door. -
Danger of burns! Water level has to be lowered as described
in “Pump filter“. Not till then pull lever beneath service flap
until door is unlocked by a gentle click. Afterwards refix all
parts.
lever
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haier Intelius 50 - HW80-B14266A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haier Intelius 50 - HW80-B14266A in the language / languages: English, German as an attachment in your email.

The manual is 14,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info