656799

Haier Intelius 50 - HW80-B14266A Manual

21
Zoom out
Zoom in
Previous page
1/56
Next page
*Warning!
Code Fb:Water-overflowprotectionis placed on deepest part of appliance.Incase of leackage
all functions will be shut down automatically except drain pump which will be activated for safety
reasons.
21
Troubleshooting
Problem Cause Solution
Washing machine fails
to operate.
s Programme is not yet started.
s Door is not properly closed.
s Machine has not been switched on
s Power failure.
s Check programme and start it.
s Close the door properly.
s Switch the machine on.
s Check power supply.
Washing machine
will not be filled with
water.
s No water.
s Inlet hose is kniked.
s Inlet hose filter is blocked.
s Water pressure is less than
0,03 MPa.
s Door is not properly closed
s Water supply failure
s Check water tap.
s Check inlet hose.
s Unblock inlet hose filter.
s Check water pressure.
s Close the door properly.
s Ensure the water supply
Machine is draining
while being filled
s Height of drain hose is below
80 cm.
s Drain hose end could reach into
water.
s Make sure that drain hose is
properly installed.
s Make sure the drain hose is
not in water
Drainage failure
s Drain hose is blocked
s Pump filter is blocked
s Drain hose end is higher than
100 cm above floor level
s Unblock drain hose.
s Clean pump filter.
s Make sure that drain hose is
properly installed
Strong vibration while
spinning
s Not all transportation bolts have
been removed.
s Appliance has no solid position.
s Machine load is not correct.
s Remove all transportation
bolts.
s Ensure solid ground and a
evelled position.
s Check load weight and balance.
Code Cause Solution
FC Electronic control - error. Contact the After sales service.
Unb Unbalanced load - error.
Check and balance laundry load in thedrum.
Reduce the load.
Troubleshooting without display code
20
Troubleshooting
Troubleshooting with display code
Many occuring problems could be solved by yourself without specific expertise. In
case of disfunction please check all shown possibilities thoroughly and follow below
instructions beforeyou contact an after sales service (see warranty card).
Code Message
Auto Automatic load detection is working.
Lo
HALF
FULL
HI
Result of the automatic load detection.
Lo = low load
HALF = half load
FULL = optimal weight load
HI = maximum load
1:25 Theremaining wash cycle time will be1hour and25minutes
06:30
Theremaining wash cycle time including chosen end-time delay will be 6hours
and 30 minutes
Lock Theappliance is in operation and the door is locked.
EndThe washing cycle is finished.The appliance shuts off automatically.
Information codes
Following codes are displayed onlyfor information referring to the washing cycle.
No measures must be performed:
Code Cause Solution
E1
Drainage error, water is not fully
drained within 6 minutes.
Check drain hose for blockage and proper
installation.
E2 Lock - error. Shut the door properly,
F3 Temperature sensor - error. Contact the After sales service.
E4
Water level not reached after 8
minutes.; Drain hose is self-
syphoning.
Make surethattap is fully opened and water
pressure is normal.
Check drain hose installation.
F4
Heating error (Appears at the end
of a cycle).
Contact the After sales service.
F7 Motor - error. Contact the After sales service.
E8 Water protective level - error. Contact the After sales service.
Fb* Water overflow.
Close tap immediately.
Contact the After sales service.
FA Water level sensor error. Contact the After sales service.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haier Intelius 50 - HW80-B14266A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haier Intelius 50 - HW80-B14266A in the language / languages: English, German as an attachment in your email.

The manual is 14,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info