Manual Haier Flexis serie (page 16 of 217) (English, German, French, Italian, Polish, Portuguese, Turkish, Spanish)

771617

Zoom out

Zoom in

1/217

1. Insert from outside the room cable into left side of the wall

hole, in which the pipe has already existed.

2. Pull out the cable on the front side, and connect the cable

making a loop.

When connecting the cable, conﬁrm the terminal number of indoor and

outdoor units carefully. If wiring is not correct, proper operation can not

be carried out and will cause defect.

Insert the cable from the back side of the unit, then pull it out on the front side.

Loosen the screws and insert the cable ends fully into terminal block, then

tighten the screws.

Pull the cable slightly to make sure the cables have been properly inserted and

tightened.

After the cable connection, never fail to fasten the connected cable with the

wiring cover.

When connecting the cable after installing the indoor unit

When connecting the cable before installing the indoor unit

Note:

1. If the supply cord is damaged, it must be replaced by the manufacturer or its

service agent or a similar qualiﬁed person. The type of connecting wire is

H07RN-F.

2. If the fuse on PC board is broken please change it with the type of

3. The wiring method should be in line with the local wiring standard.

4. After installation, the power plug should be easily reached.

5. A breaker should be incorporated into ﬁxed wiring. The breaker should be

all-pole switch and the distance between its two contacts should be not less

than 3mm.

T.3.15A/250VAC (Indoor).

To Outdoor unit

Connecting wiring

4G1.0mm

C od e

indication Tro uble description Analyze and diag nose

E14

H ea t-e xc han ge

sen sor failure

In doo r E EP R O M

erro r

C om m un ic atio n

fa ult be tw ee n

indoo r and o utdo or

units

Ind oo r fan m otor

m alfunction

O peration halt due to b rea king

of wire inside the fan m otor;

O peration ha lt due to breaking

of the fan m otor lead w ires;

D etection error due to faulty

ind oor u nit P C B ;

Indoor unit- outdoor unit signal

transm ission error due to w irin g

error;

F aulty P C B ;

F aulty E E P R O M da ta;

F aulty E E P R O M ;

F aulty P C B ;

Fa ulty connector connection;

Fa ulty th erm is tor;

F aulty P C B ;

Room temperature

sensor failure

The power source must be exclusively used for air conditioner.

In the case of installing an air conditioner in a moist place, please install

an ea

For installation in other places, use a circuit breaker as far as possible.

Pipe cutting is carried out with a pipe cutter and burs must be removed.

After inserting the ﬂare nut, ﬂaring work is carried out.

Power Source Installation

Cutting and Flaring Work of Piping

Flare tool for R410A Conventional ﬂare tool

Clutch-type clutch-type(Rigid-type) Wing-nut type (Imperial-type)

A 0~0.5mm 1.0~1.5mm 1.5~2.0mm

rth leakage breaker.

Lean Damage of ﬂare Partial Too outside

tcerrocnItcerroC

On Drainage

It becomes

high midway. The gap with the

ground is too small.

There is the bad

smell from a ditch

It waves.

The end is imm-

ersed in water.

Please install the drain hose so as to be downward slope without fail.

Please don’t do the drainage as shown below.

Please pour water in the drain pan of the indoor unit, and

is carried out surely to outdoor.

In case that the attached drain hose is in a room, please apply heat

insulation to

Less than

5cm

conﬁrm that

drainage

it without fail.

Crack

Indoor unit

Check Items for Test Run

Gas leak from pipe connecting?

Heat insulation of pipe connecting?

Are the connecting wirings of indoor and outdoor ﬁrmly

Is the connecting wiring of indoor and outdoor ﬁrmly ﬁxed?

Is drainage securely carried out?

Is the earth line securely connected?

Is the indoor unit securely ﬁxed?

Is power source voltage abided by the code?

Is there any noise?

Is the lamp normally lighting?

Are cooling and heating (when in heat pump) performed normally?

Is the operation of room temperature regulator normal?

Please kindly explain to our customers how to

operate through the instruction manual.

inserted to the terminal block?

Put check mark in boxes

Flare tooling die 1.Cut pipe 2.Remove burs

3.Insert the ﬂare nut 4.Flare pipe

On Drainage

Check for Installation and Test Run

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Haier Flexis serie in the language / languages: English, German, French, Italian, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 109.37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haier Flexis serie

Haier Flexis serie User Manual - Dutch - 19 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Haier Flexis serie Manual

Product: