Manual Haier Flexis serie (page 15 of 217) (English, German, French, Italian, Polish, Portuguese, Turkish, Spanish)

771617

Zoom out

Zoom in

1/217

Indoor Unit Installation

Fix to side bar and lintel a mounting bar, Which is separately sold, and

then fasten the plate to the fixed mounting bar.

Refer to the previous article, “ When the mounting plate is fi

position of wall hole.

Make a hole of 60 mm in diameter, slightly descending to outside the wall

Install piping hole cover and seal it off with putty after installation

1. Carry out, based on the neighboring pillars or lintels, a

to be fixed against the wall, then temporarily fasten the plate

with one steel nail.

2. Make sure once more the proper level of the plate, by hanging a thread

with a weight from the central top of the plate, then fasten securely the

plate with the attachment steel nail.

3. Find the wall hole location A/C using a measuring tape

When the mounting plate is fixed side bar and lintel

Fitting of the Mounting Plate and Positioning of the wall Hole

Lid for right

piping

Lid for under piping pipe

Fix with adhesive tape

Lid for left piping

Indoor/outdoor electric cable and drain hose must be bound with

efrigerant piping by protecting tape.

[ Other direction piping ]

Cut away, with a nipper, the lid for piping according to the piping

direction and then bend the pipe according to theposition of wall

hole. When bending, be careful not to crash pipes.

Connect beforehand the indoor/outdoor electric cable, and then

pull out the connected to the heat insulation of connecting part

specially.

proper leveling

for the plate

rst fixed “,

for the

Making a Hole on the Wall and Fitting the Piping Hole Cover

Drawing of pipe

Installation of the Indoor Unit

[ Rear piping ]

Draw pipes and the drain hose, then fasten them with the adhesive tape

[ Left Left-rear piping ]

In case of left side piping, cut away, with a nipper, the lid for left

piping.

In case of left-rear piping, bend the pipes according to the piping

direction to the mark of hole for left-rear piping which is marked on

heat insulation materials.

1. Insert the drain hose into the dent of heat insulation materials of

indoor unit.

2. Insert the indoor/outdoor electric cable from backside of indoor

unit,and pull it out on the front side, then connect them.

3. Coat the flaring seal face with refrigerant oil and connect pipes.

Cover the connection part with heat insulation materials closely,

and make sure fixing with adhesive tape

Hang surely the unit body onto the upper

notches of the mounting plate. Move the body

from side to side to verify its secure fixing.

In order to fix the body onto the mounting

plate,hold up the body aslant from the

underside and then put it down perpendicularly.

Remove terminal cover at right bottom corner of

indoor unit, then take off wiring cover by removing

its screws.

mounting plate

When you unload the indoor unit,please use your hand to arise

slightly and lift the unit aslant until it leaves the mounting plate.

agraffe mounting plate

the body to leave agraffe,then lift the bottom of the body outward

Heat insulation

material

Drain hose

Piping

Pipe supporting

plate

Indoor/outdoor electric cable

Indoor side Outdoor side

Ø60mm

Wall hole

Thickness of wall

(Section of wall hole) Piping hole pipe

When the mounting plate is first fixed

Fixing the indoor unit body

Unloading of indoor unit body

Connecting the indoor/outdoor Electric Cable

Removing the wiring cover

A=170mm C=130mm B=

60mm

D=47mm

A=222mm C=165mm B=

60mm

D=41.5mm

A=218mm C=151mm

60mm

D=38.5mm D=38.5mm

9K/12K/15K

18K

24K

D=47mm

(20/25/35/42)

(50)

(71)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Haier Flexis serie in the language / languages: English, German, French, Italian, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 109.37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haier Flexis serie

Haier Flexis serie User Manual - Dutch - 19 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Haier Flexis serie Manual

Product: