811877
3
Zoom out
Zoom in
Previous page
1/12
Next page
3
2. When using the fire protection insulating set, mount the two rear wall screen panels (see
installation instructions of the fire protection insulating set) to the rear wall of the fireplace.
3. Adjust the fireplace to the correct height using the open-end wrench size 13mm by turning the
adjustable feet. The ideal height is shown in Figure 2. For comparison, install the base with the
base plate. The lower edge of the panel with air damper on the fireplace can end flush with the
sub-structure of the concrete lining or be approximately 1 to 2 mm higher (Attention: The
gluing will result in a minimal change of the overall height: however it is possible to
subsequently adjust the correct height by turning the adjustable feet).
4. In addition to this the distance to the screen wall must be adjusted to the correct dimension (see
Figure 2).
Important: After this, adjust the fireplace horizontally using the water level.
5. Locate the flue pipe connection (e.g. with double wall lining) in the chimney (see installation
and operating instructions of the fireplace).
6. Now start installing the kit.
6 INSTRUCTIONS
It is not permissible to install the kit by gluing the elements together without protecting the fireplace
hood against slipping!
Following the installation, place the refractory lining in the fire chamber of your fireplace (see
equipment sheet of your fireplace). Why refractories last? Because the fireplace can be easier
repositioned while assembling the artificial stone kit.
To avoid minor joints between the kit and the wall we recommend to grout these with acrylic
compound (in contrast with silicon, acrylic can be painted over immediately).
Once the fireplace kit has dried, the fireplace can be painted (mineral-based paint, no depth primer
required). In order to achieve a fine-grain structure, simply mix some adhesive into the paint for
the first coat. Use only paint for the second coat. Of course roll-on or rub-on plasters can also be
used to finish the surface.
Allow the fireplace kit to dry for at least two weeks before initial start-up.
To start the fireplace: Carefully read the operating instructions and start the fireplace using little
wood. After approximately one hour the device can be heated to rated heat.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn Roma II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn Roma II in the language / languages: English as an attachment in your email.

The manual is 0.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn Roma II

Haas-Sohn Roma II User Manual - German - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info