564777
22
Zoom out
Zoom in
Previous page
1/31
Next page
22
Error number 6 or 9
Cause:
The door is open for longer than 1 minute
during operation
The damper at the bottom of the door is
not in the right position
Cable broken in the electric wiring to the
door contact switch
The connector has come out on the door
contact switch or on the central unit
Correction:
Close the door
Move the damper at the bottom of the
door to the right position so that the
switch is operated when the door is
closed
Check door contact switch, cable and
connector
Error number 7
Cause:
Flue gas temperature sensor defective or
not connected
Correction
Contact the service engineer
Error number 8
Cause:
Flue gas temperature sensor defective
Correction:
Contact the service engineer
Error number 11
Cause:
Room temperature sensor defective or
not connected
Correction:
Contact the service engineer
Error number 12
Cause:
Room temperature sensor defective
Correction:
Contact the service engineer
Error number 15
Cause: The induced draught fan is not
running at the correct rotation
speed
The following circumstances might lead to this:
Induced draught fan defective
Connection cable from the rotation speed
sensor (Hallsensor) is broken or poor
contact in the connector on this
connection cable
Electricity supply to the fan motor
interrupted
Correction:
Contact the service engineer
Error number 17
Cause:
The connection between the central unit
and the operator console is interrupted.
The following circumstances might lead to this:
Connection cable is not connected to the
operator console or to the central unit
Connection cable is damaged
Correction:
Check that the connection cable is
connected to both units, the operator
console and the central unit.
Contact the service engineer
Error number 18
Cause:
A safety shutdown was triggered after a
power cut
Correction:
Clear the fault on the operator console
and restart the device
Error number 21
Cause:
Temperature fell below the minimum
temperature in Heating mode operating
status
The following circumstances might lead to this:
No pellets present
The screw conveyor is not rotating, it is
jammed, the screw conveyor motor is
defective or the chute is not clear
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn HSP2.PREMIUM.17 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn HSP2.PREMIUM.17 in the language / languages: English as an attachment in your email.

The manual is 7.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn HSP2.PREMIUM.17

Haas-Sohn HSP2.PREMIUM.17 Usermanual and installation guide - German - 32 pages

Haas-Sohn HSP2.PREMIUM.17 User Manual - French - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info